Nissan Rogue (T33) 2021-Present Service Manual: Calibration of Decel G Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Basic Inspection / Calibration of Decel G Sensor

Description

CAUTION:

Always perform the decel G sensor calibration before driving when the following operation is performed. Refer to Work Procedure.

×: Required —: Not required

Procedure Decel G sensor calibration
Removing/ installing ABS actuator and electric unit (control unit) ×
Replacing ABS actuator and electric unit (control unit) ×
Removing/installing steering components —
Replacing steering components —
Removing/installing front suspension components —
Replacing front suspension components —
Removing/installing tire —
Replacing tire —
Tire rotation —
Adjusting front wheel alignment. —

Work Procedure

CAUTION:

Always use CONSULT for the decel G sensor calibration. (It cannot be adjusted other than CONSULT.)

CHECK THE VEHICLE STATUS

  1. Steer the steering wheel to the straight-ahead position. Stop the Nissan Ariya vehicle on level surface.

  2. Stop the engine.

  3. Ignition switch OFF (Auto ACC function OFF).

Is the Nissan Ariya vehicle stopped in the straight-ahead position on level surface?

YES>>

GO TO 2.

NO>>

Steer the steering wheel to the straight-ahead position. Stop the Nissan Ariya vehicle on level surface.

PERFORM DECEL G SENSOR CALIBRATION

CAUTION:

  • Never allow passenger or load on the Nissan Ariya vehicle.

  • Never apply vibration to the vehicle body when opening or closing door during calibration.

CONSULT

  1. Ignition switch ON.

    CAUTION:

    Never start engine.

  2. Select “ABS”, “Work support”, “DECEL G SENSOR CALIBRATION” in this order.

  3. Select “START”.

  4. After approximately 10 seconds, select “END”.

  5. Ignition switch OFF (Auto ACC function OFF) and then it ON again.

    CAUTION:

    Be sure to perform the operation above.

>>

GO TO 3.

CHECK Data monitor

CONSULT

  1. Drive the Nissan Ariya vehicle. Steer the steering wheel to the straight-ahead position. Stop the vehicle on level surface.

  2. Select “ABS”, "Data monitor", and “Decel G sensor” in this order. Check that the signal is within the specified value. Refer to Reference Value.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 1.

ERASE SELF-DIAGNOSIS MEMORY

CONSULT

Erase self-diagnosis result of “ABS”.

Are the memories erased?

YES>>

End of work.

NO>>

Check the items indicated by the self-diagnosis.

    Adjustment of Steering Angle Sensor Neutral Position
    Description Always adjust the neutral position of steering angle sensor before driving when the following operation is performed. Refer to Work Procedure.×: Required —: Not r...
    Adjustment of Brake Caliper Initial Position
    Description CAUTION: When performing the following operations, always use CONSULT (It cannot be performed by any means other than CONSULT.), for performing "INITIALIZATION POSIT...

    Other materials:

    P1564 Ascd Steering Switch
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1564 00 ASCD SW (ASCD SW) Diagnosis condition — Signal (terminal) ASCD steering switch signal Threshold ECM detects that input signal from t ...

    High Pressure Fuel Pump
    Component Function Check CHECK HIGH PRESSURE FUEL PUMP FUNCTION With CONSULT Start engine. Select “FUEL PRES SEN V” in “DATA MONITOR” mode of “ENGINE” using CONSULT and check the indication as per the following conditions. Monitor item Condition Indication FUEL PRES ...

    Dtc/circuit Diagnosis. C1700-54 Control Unit
    DTC Description NOTE: The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information. Activate and display TPMS sensor IDs Display tire pressure reported by the TPMS sensor Read TPMS DTCs ...