Nissan Rogue (T33) 2021-Present Service Manual: Adjustment of Steering Angle Sensor Neutral Position

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Basic Inspection / Adjustment of Steering Angle Sensor Neutral Position

Description

Always adjust the neutral position of steering angle sensor before driving when the following operation is performed. Refer to Work Procedure.

×: Required —: Not required

Procedure Adjust the neutral position of steering angle sensor
Removing/ installing ABS actuator and electric unit (control unit) —
Replacing ABS actuator and electric unit (control unit) ×
Removing/installing steering angle sensor ×
Replacing steering angle sensor ×
Removing/installing steering components ×
Replacing steering components ×
Removing/installing front suspension components ×
Replacing front suspension components ×
Removing/installing tire —
Replacing tire —
Tire rotation —
Adjusting front wheel alignment. ×

Work Procedure

CAUTION:

Always use CONSULT when adjusting the neutral position of steering angle sensor. (It cannot be adjusted other than CONSULT.)

CHECK THE VEHICLE STATUS (1)

Stop vehicle with front wheels in the straight-ahead position.

Does the Nissan Ariya vehicle stay in the straight-ahead position?

YES>>

GO TO 2.

NO>>

Steer the steering wheel to the straight-ahead position. Stop the Nissan Ariya vehicle.

ADJUST NEUTRAL POSITION OF STEERING ANGLE SENSOR

CONSULT

  1. Ignition switch ON.

    CAUTION:

    Never start engine.

  2. Select “ABS”, “Work support” and “ST ANGLE SENSOR ADJUSTMENT” in this order.

  3. Select “START”.

    CAUTION:

    Never touch steering wheel while adjusting steering angle sensor.

  4. After approximately 10 seconds, select “END”.

  5. Ignition switch OFF (Auto ACC function OFF), and then it ON again.

    CAUTION:

    Be sure to perform the operation above.

>>

GO TO 3.

CHECK Data monitor (1)

CONSULT

  1. The Nissan Ariya vehicle is either pointing straight ahead, or the vehicle needs to be moved. Stop when it is pointing straight ahead.

  2. Select “ABS”, "Data monitor", and “Steering angle” in the order. Check that the signal is within the specified value. Refer to Reference Value.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

GO TO 4.

CHECK STEERING COMPONENT PARTS

Check the installation condition of steering component parts. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts. GO TO 5.

CHECK FRONT SUSPENSION COMPONENT PARTS

Check the installation condition of front suspension component parts. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts. GO TO 6.

CHECK FRONT WHEEL ALIGNMENT

Check the front wheel alignment. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Adjust the front wheel alignment. Refer to Adjustment. GO TO 7.

CHECK THE Nissan Ariya Vehicle STATUS (2)

Stop vehicle with front wheels in the straight-ahead position.

Does the Nissan Ariya vehicle stay in the straight-ahead position?

YES>>

GO TO 8.

NO>>

Steer the steering wheel to the straight-ahead position. GO TO 8.

CHECK Data monitor (2)

CONSULT

  1. The Nissan Ariya vehicle is either pointing straight ahead, or the vehicle needs to be moved. Stop when it is pointing straight ahead.

  2. Select “ABS”, "Data monitor", and “Steering angle” in the order. Check that the signal is within the specified value. Refer to Reference Value.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

GO TO 9.

CHECK Data monitor (3)

CONSULT

  1. The Nissan Ariya vehicle is either pointing straight ahead, or the vehicle needs to be moved.

    CAUTION:

    • Drive the Nissan Ariya vehicle at approximately 30 km/h (19MPH) or more for 300 m (985 ft) or more.

    • Never use tester

  2. The Nissan Ariya vehicle is either pointing straight ahead, or the vehicle needs to be moved. Stop when it is pointing straight ahead.

  3. Select “ABS”, "Data monitor", and “Steering angle” in the order. Check that the signal is within the specified value. Refer to Reference Value.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

GO TO 1.

ERASE SELF-DIAGNOSIS MEMORY

CONSULT

  1. Record or print self-diagnosis results and freeze frame data (FFD).

  2. Erase self-diagnosis result of “ABS”.

Are the memories erased?

YES>>

GO TO 11.

NO>>

Check the items indicated by the self-diagnosis.

EPS LEARNING

  1. Pull the parking brake switch.

    NOTE:

    Check the parking brake switch indicator is turn On.

  2. Ignition switch OFF.

  3. Get out of the Nissan Ariya vehicle and close all doors.

  4. Wait 65 seconds.

    NOTE:

    • Check the parking brake switch indicator turn OFF.

    • If the rear brake caliper is heated, wait an hour so that parking brake switch indicator does not turn OFF.

  5. Start the engine.

    CAUTION:

    Never drive the Nissan Ariya vehicle.

>>

End of work.

    Configuration
    Description Vehicle specification needs to be written with CONSULT because it is not written after replacing the ABS actuator and electric unit (control unit).The configuration ...
    Calibration of Decel G Sensor
    Description CAUTION: Always perform the decel G sensor calibration before driving when the following operation is performed. Refer to Work Procedure. ×: Required —: Not requi...

    Other materials:

    Dtc/circuit Diagnosis. U0075-00 Communication Bus C Off
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition U0075-00 Control module comm Bus C Off (Control module communication Bus C Off) Diagnosis condition Ignition switch ON Signal (terminal) CAN communication s ...

    System maintenance
    To ensure proper operation of the driver monitoring system on the Nissan Rogue, keep the camera and surrounding area clean. Use a soft, damp cloth—such as one designed for lens cleaning—wrung out thoroughly, and gently wipe the surface to remove dust or dirt. License information (ProPILOT Ass ...

    Power Supply and Ground Circuit
    8ch Can Gateway Diagnosis Procedure CHECK FUSE Check that the following fuse are not blown. Signal name Fuse No. Battery power supply 16 Ignition power supply 9 Is the fuse blown (open)? YES>> Replace the blown fuse after repairing the affected circuit if a fuse ...