Nissan Rogue (T33) 2021-Present Service Manual: C10b3-68 Parking Brake Control Module

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Dtc/circuit Diagnosis / C10b3-68 Parking Brake Control Module

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C10B3 68

Parking brake control module

(Parking brake control module) 		Diagnosis condition When ignition switch is ON
Signal (terminal) —
Threshold When an internal malfunctioning in the ABS actuator and electric unit (control unit) (Maintenance mode).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

NOTE:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC CRNT DTC

  • Harness or connector

  • Parking brake actuator

  • Rear brake caliper assembly

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

  • Harness or connector

  • Parking brake actuator

  • Rear brake caliper assembly

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

FAIL-SAFE

The following functions are suspended.

Electric parking brake function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF) to ON.

  2. Push the parking brake switch.

    CAUTION:

    • Set the electric shift selector in the P position.

    • Depress the brake pedal.

  3. Pull the parking brake switch.

  4. Perform self-diagnosis for “ABS”.

Is DTC “C10B3-68” detected?

YES-1>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

PROGRAMING OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

Perform programing of ABS actuator and electric unit (control unit). Refer to Work Procedure.

>>

GO TO 2.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Ignition switch ON.

    CAUTION:

    Be sure wait of 10 seconds after ignition switch ON.

  2. Perform self-diagnosis for “ABS”.

Is DTC “C10B3-68” detected?

YES-1>>

"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

Inspection End

    C10b3-55 Parking Brake Control Module
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C10B3 55 Parking brake control module (Parking brake control...
    C10b4-98 Overheat
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C10B4 98 Overheat (Overheat) Diagnosis condition When igniti...

    Other materials:

    System Description. Diagnosis System (occupant Detection System Control Unit)
    CONSULT Function APPLICATION ITEMCONSULT performs the following functions. Diagnosis mode CGW Status Description Restricted Mode Diag Test Mode Open Mode CGW Information Display Display Display Display the current CGW mode Enables CGW to switch mode Data mo ...

    C1203-86 Abs Signal
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition C1203-86 ABS SYSTEM (Antilock brake system) Diagnosis condition Ignition switch: ON Nissan Ariya Vehicle running Signal Wheel speed signals ...

    Steering Switch Signal B Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL CONSULT Ignition switch ON. Select “Steering switch input” in “Data monitor” mode of “M&A”. Check that the function operates normally according to the following conditions: Condition Value CONTRO ...