Nissan Rogue (T33) 2021-Present Service Manual: C10b4-98 Overheat
DTC Description
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B4 | 98 |
Overheat (Overheat) |
Diagnosis condition | When ignition switch is ON | |
| Signal (terminal) | — | ||||
| Threshold | System is high temperature status. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
DTC CONFIRMATION PROCEDURE
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.
>>
GO TO 2.
CHECK DTC DETECTION
CONSULT
-
Ignition switch OFF (Auto ACC function OFF) to ON.
-
Push the parking brake switch.
CAUTION:
-
Set the electric shift selector in the P position.
-
Depress the brake pedal.
-
-
Pull the parking brake switch.
-
Perform self-diagnosis for “ABS”.
Is DTC “C10B4–98” detected?
YES-1>>“CRNT” is displayed: Refer to Diagnosis Procedure.
YES-2>>“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: Inspection End
Diagnosis Procedure
PERFORM SELF-DIAGNOSIS (1)
CONSULT
-
Erase self-diagnosis result for “ABS”.
-
After approximately 1 minute, operate (pull and push) parking brake switch.
CAUTION:
-
Set the electric shift selector in the P position.
-
Depress the brake pedal
-
-
Perform self-diagnosis for “ABS”.
Is DTC “C10B4-98” detected?
YES>>Check when parking brake actuator is stuck.
NO>>GO TO 2.
PERFORM SELF-DIAGNOSIS (2)
CONSULT
-
Operate and release the parking brake five times.
CAUTION:
-
Set the electric shift selector in the P position.
-
Depress the brake pedal
-
-
Perform self-diagnosis for “ABS”.
Is DTC “C10B4-98” detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
YES-2>>“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)
NO>>Inspection End
Other materials:
Electrical Incident Inspection
Work Flow
WORK FLOW STEP DESCRIPTION
STEP 1
Get detailed information about the conditions and the environment when the incident occurred.
The following are key pieces of information required to make a good analysis:
WHAT
Nissan Ariya Vehicle Model, Engine, Transmission/Transaxle an ...
Fuel Pressure Check
Work Procedure
FUEL PRESSURE RELEASEFUEL PRESSURE RELEASE
With CONSULT
Turn ignition switch ON.
Perform “ENGINE” in “WORK SUPPORT” mode with CONSULT.
Start the engine.
After engine stalls, crank it two or three times to release all fuel pressure.
Turn ignition swit ...
Removal and Installation. Steering Member Assembly
Exploded View
Steering member brace
Steering member assembly
Removal and Installation
Remove instrument panel assembly. Refer to Removal and Installation.
Remove driver knee air bag. Refer to Removal and Installation.
Remove passenger knee air bag. Refer to Remova ...