Nissan Rogue (T33) 2021-Present Service Manual: C10b6-68 Parking Brake System
DTC Description
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | |||
|---|---|---|---|---|---|
| C10B6 | 68 |
Parking brake system (Parking brake system) |
Diagnosis condition | When parking brake is apply | |
| Signal (terminal) | — | ||||
| Threshold | When an electric parking brake system is malfunctioning. | ||||
| Diagnosis delay time | 1 second or less | ||||
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
| PAST DTC | CRNT DTC |
|---|---|
|
|
FAIL-SAFE
The following functions are suspended.
Electric parking brake function
DTC CONFIRMATION PROCEDURE
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.
>>
GO TO 2.
CHECK DTC DETECTION
CONSULT
-
Ignition switch OFF (Auto ACC function OFF) to ON.
-
Push the parking brake switch.
CAUTION:
-
Set the electric shift selector in the P position.
-
Depress the brake pedal.
-
-
Pull the parking brake switch.
-
Perform self-diagnosis for “ABS”.
Is DTC “C10B6–68” detected?
YES-1>>“CRNT” is displayed: Refer to Diagnosis Procedure.
YES-2>>“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: Inspection End
Diagnosis Procedure
CHECK REAR BRAKE COMPONENT PARTS
-
Apply and release the parking brake.
-
Disconnect 12V battery negative terminal.
-
Check rear brake component parts.
-
Rear brake pad: Refer to Inspection and Adjustment.
-
Rear brake caliper assembly and parking brake actuator: Refer to Inspection and Adjustment.
-
Rear disc rotor: Refer to Inspection and Adjustment.
-
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace error-detected parts. GO TO 2.
PERFORM SELF-DIAGNOSIS
CONSULT
-
Connect 12V battery negative terminal.
-
Ignition switch ON.
CAUTION:
Be sure wait of 10 seconds after ignition switch ON.
-
Apply and release the parking brake five times.
-
Perform self-diagnosis for “ABS”.
Is DTC “C10B6–68” detected?
YES-1>>"CRNT" is displayed: Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.
YES-2>>“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)
NO>>Inspection End
Other materials:
Oil Level Sensor Signal Circuit
DiagnosisProcedure
CHECK OIL LEVEL SENSOR CIRCUIT
Ignition switch OFF.
Disconnect combination meter harness connector and oil level sensor harness connector.
Check continuity between combination meter harness connector and oil level sensor harness connector.
Combination meter
Oi ...
Removal and Installation. Door Mirror
Exploded View
Door mirror cover (with side turn signal lamp)
Door mirror finisher
Side turn signal lamp (with side turn signal lamp)
Door mirror base
Door mirror actuator
Glass mirror
Blind cap
Side camera (with side camera)
Side camera bracket (with s ...
Precaution. Precautions
Precautions for Removing Battery Terminal
With the adoption of Auto ACC function, ACC power is automatically
supplied by operating the Intelligent Key or remote keyless entry or by
opening/closing the driver side door. In addition, ACC power is supplied
even after the ignition switch is i ...