Nissan Rogue (T33) 2021-Present Service Manual: C1051-04 Pump Motor

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Dtc/circuit Diagnosis / C1051-04 Pump Motor

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1051 04

Pump motor

(Pump motor) 		Diagnosis condition

  • When ignition switch is ON.

  • When the power supply voltage is normal.
Signal (terminal) -
Threshold When a malfunction is detected in motor or motor relay.
Diagnosis delay time 12 seconds or less

POSSIBLE CAUSE

NOTE:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC CRNT DTC

  • Harness or connector

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

  • Harness or connector

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

FAIL-SAFE

The following functions are suspended.

  • VDC function

  • TCS function

  • ABS function

  • EBD function

  • Brake limited slip differential (BLSD) function

  • Brake assist function

  • Brake force distribution function

  • hill start assist function

  • Electric parking brake function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF) to ON, and wait 30 seconds.

  2. Drive the Nissan Ariya vehicle at approximately 50 km/h (31 MPH) or more for approximately 2 minutes.

  3. Stop the vehicle.

  4. Ignition switch OFF (Auto ACC function OFF).

  5. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  6. Perform self-diagnosis for “ABS”.

Is DTC “C1051-04” detected?

YES-1>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK CONNECTOR

  1. Disconnect 12V battery negative terminal.

  2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 2.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Connect 12V battery negative terminal, and wait 30 seconds.

  2. Drive the Nissan Ariya vehicle at approximately 50 km/h (31 MPH) or more for approximately 2 minutes.

    NOTE:

    Nissan Ariya Vehicle must be driven after repair or replacement to erase the previous DTCs.

  3. Stop the Nissan Ariya vehicle.

  4. Ignition switch OFF (Auto ACC function OFF).

  5. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  6. Perform self-diagnosis for “ABS”.

Is DTC “C1051-04” detected?

YES>>

GO TO 3.

NO>>

Inspection End

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 4.

ERASE SELF-DIAGNOSIS RESULT (1)

CONSULT

  1. Drive the Nissan Ariya vehicle at approximately 50 km/h (31 MPH) or more for approximately 2 minutes.

    NOTE:

    Nissan Ariya Vehicle must be driven after repair or replacement to erase the previous DTCs.

  2. Stop the Nissan Ariya vehicle.

  3. Erase self-diagnosis result for “ABS”.

  4. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

>>

Inspection End

CHECK TERMINAL

  1. Disconnect 12V battery negative terminal.

  2. Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

ERASE SELF-DIAGNOSIS RESULT (2)

CONSULT

  1. Connect 12V battery negative terminal.

  2. Drive the Nissan Ariya vehicle at approximately 50 km/h (31 MPH) or more for approximately 2 minutes.

    NOTE:

    Nissan Ariya Vehicle must be driven after repair or replacement to erase the previous DTCs.

  3. Stop the Nissan Ariya vehicle.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

>>

Inspection End

    C1042-04 Cut Valve 1
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1042 04 Cut valve 1 (Cut valve 1) Diagnosis condition When ...
    C1055-49 Can System
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1055 49 CAN system [Controller area network system] 1 Diagn...

    Other materials:

    Rear View Monitor. System Description
    Component Parts Component Parts Location No. Component Function 1. Rear view camera Refer to Rear View Camera. 2. AV control unit Refer to AV Control Unit. 3. TCM (Transmission Control Module) Provides AV control unit with the shift position signal via CAN commu ...

    Evap Canister Vent Control Valve
    Component Inspection CHECK EVAP CANISTER VENT CONTROL VALVE-1 Disconnect hose from (A), (B), and (C) with remaining harness connector connected. Block port (B). Blow air into port (A) and check that it flows freely out of port (C). Is sufficient air flowed from port (C)? YES& ...

    Windows
    Power windows Basic information WARNING Make sure all passengers keep their hands and other body parts inside the vehicle while it is moving and before you close the windows. Use the window lock switch to help prevent unintended operation of the power windows. To help avoid the risk of injury or ...