Nissan Rogue (T33) 2021-Present Service Manual: C1055-49 Can System

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Dtc/circuit Diagnosis / C1055-49 Can System

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1055 49

CAN system

[Controller area network system] 		1 Diagnosis condition

  • When ignition switch is ON.

  • When the power supply voltage is normal.
Signal (terminal) CAN communication signal
Threshold When CAN communication signal is not continuously transmitted from ABS actuator and electric unit (control unit).
Diagnosis delay time 2 seconds or more
2 Diagnosis condition

  • When ignition switch is ON.

  • When the power supply voltage is normal.
Signal (terminal) CAN communication signal
Threshold When CAN communication signal is not continuously received from ABS actuator and electric unit (control unit).
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

NOTE:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC CRNT DTC

  • Harness or connector

  • CAN communication line

 CAN communication system

FAIL-SAFE

The following functions are suspended.

  • VDC function

  • TCS function

  • Brake limited slip differential (BLSD) function

  • Brake assist function

  • Brake force distribution function

  • hill start assist function

  • Electric parking brake function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C1055-49” detected?

YES-1>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

Refer to Trouble Diagnosis Flow Chart.

    C1051-04 Pump Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1051 04 Pump motor (Pump motor) Diagnosis condition When ig...
    C1056-13 Battery Power Supply
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1056 13 Battery power supply (Battery power supply) Diagnos...

    Other materials:

    Rear window and outside mirror defroster switch
    Example To defog or defrost the rear window and outside mirrors (if equipped), start the engine and press the switch. The indicator light A illuminates. Press again to turn the system off. The system turns off automatically after approximately 20 minutes. CAUTION When cleaning the inside of the ...

    Poste de conduite
    Le poste de conduite du Nissan Rogue regroupe les commandes de conduite, d’assistance et de confort. Familiarisez-vous avec l’emplacement des commandes au volant et des systèmes d’aide avant de rouler, surtout si vous changez de version ou de finition. Commande Direction assistée* (m ...

    On Board Diagnostic (obd) System
    Diagnosis Description This system is an on board diagnostic system that records exhaust emission-related diagnostic information and detects a sensors/actuator-related malfunction. A malfunction is indicated by the malfunction indicator lamp (MIL) and stored in ECU memory as a DTC. The diagn ...