Nissan Rogue (T33) 2021-Present Service Manual: C1042-04 Cut Valve 1

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Dtc/circuit Diagnosis / C1042-04 Cut Valve 1

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1042 04

Cut valve 1

(Cut valve 1) 		Diagnosis condition

  • When ignition switch is ON.

  • When the power supply voltage is normal.
Signal (terminal) -
Threshold When a malfunction is detected in cut valve 1.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

NOTE:

Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.

PAST DTC CRNT DTC

  • Harness or connector

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

  • Harness or connector

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

FAIL-SAFE

The following functions are suspended.

  • VDC function

  • TCS function

  • ABS function

  • EBD function

  • Brake limited slip differential (BLSD) function

  • Brake assist function

  • Brake force distribution function

  • hill start assist function

  • Electric parking brake function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  3. Perform Self diagnosis result for “ABS”.

Is DTC “C1042-04” detected?

YES-1>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES-2>>

“PAST” is displayed: Inspection End (Erase the memory of Self diagnosis result.)

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK CONNECTOR

  1. Disconnect 12V battery negative terminal.

  2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 2.

PERFORM SELF DIAGNOSIS RESULT

CONSULT

  1. Connect 12V battery negative terminal.

  2. Start the engine.

    NOTE:

    Wait at least 10 seconds after start the engine.

  3. Perform Self diagnosis result for “ABS”.

Is DTC “C1042-04” detected?

YES>>

GO TO 3.

NO>>

Inspection End

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link.

CHECK TERMINAL

  1. Disconnect 12V battery negative terminal.

  2. Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Repair / replace harness, connector, or terminal.

    C1041-55 Configuration
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1041 55 Configuration (Configuration) Diagnosis condition W...
    C1051-04 Pump Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1051 04 Pump motor (Pump motor) Diagnosis condition When ig...

    Other materials:

    P2123 App Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2123 00 APP SEN 1/CIRC (Throttle/Pedal position sensor/switch D circuit high) Diagnosis condition Engine running at idle Signal (terminal) Accelerator ...

    Can Fundamental. Basic Inspection. Diagnosis and Repair Work Flow
    Diagnosis and Repair Work Flow Trouble Diagnosis Flow Chart DESCRIPTIONDETAIL OF TROUBLE DIAGNOSIS FLOW CHARTINTERVIEW WITH CUSTOMER Interview with the customer is important to detect the root cause of CAN communication system errors and to understand Nissan Ariya vehicle condition and sympto ...

    P044c Egr Volume Control Valve Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P044C 00 EGR SENSOR C (EGR sensor C circuit low) Diagnosis condition Ignition switch ON Signal (terminal) EGR volume control valve signal Threshol ...