Nissan Rogue (T33) 2021-Present Service Manual: Tcm Branch Line Circuit (drivetrain Can Communication 1 Circuit)

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Lan System / Can :: Dtc/circuit Diagnosis / Tcm Branch Line Circuit (drivetrain Can Communication 1 Circuit)

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the terminals and connectors of the TCM for damage, bend and loose connection (unit side and connector side).

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Disconnect the connector of TCM.

  2. Check the resistance between the TCM harness connector terminals.

    TCM harness connector Resistance (Ω)
    Connector No. Terminal No.
    F115 17 16 Approx. 54 – 66

Is the measurement value within the specification?

YES>>

GO TO 6.

NO>>

GO TO 3.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Disconnect the CVT unit connector.

  2. Check the resistance between the CVT unit connector terminals.

    CVT unit connector Resistance (Ω)
    Connector No. Terminal No.
    F70 11 4 Approx. 54 – 66

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair the TCM branch line.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Remove the terminal assembly B. Refer to Removal and Installation.

  2. Check the continuity between the terminal assembly B.

    Connector F115 side Connector F114 side Continuity
    Terminal No. Terminal No.
    17 11 Existed
    16 4 Existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair the terminal assembly B.

CHECK HARNESS FOR OPEN CIRCUIT

Check the continuity between the terminal assembly A.

Connector F114 side Connector F70 side Continuity
Terminal No. Terminal No.
11 11 Existed
4 4 Existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair the terminal assembly A.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the TCM. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES (Present error)>>

Replace the TCM. Refer to Removal and Installation.

YES (Past error)>>

Error was detected in the TCM branch line.

NO>>

Repair the power supply and the ground circuit.

    Ssg Branch Line Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the terminals and connectors of the sub starter ...
    Evtc Branch Line Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the terminals and connectors of the electric int...

    Other materials:

    Awd. Service Data and Specifications (sds). Service Data and Specifications (sds)
    Service Data and Specifications (sds) Wheel Bearing Axial end play 0.05 mm (0.002 in) or less Drive Shaft Item   Standard Grease quantity Wheel side 49 – 69 g (1.73 – 2.43 oz) Final drive side 78 – 98 g (2.76 – 3.45 oz) Boots installed length* Wheel ...

    Comment activer/désactiver le système de sonar
    Commandes au volant (côté gauche) Écran d’informations du véhicule Le système de sonar du Nissan Rogue est automatiquement activé lorsque le contact d’allumage est placé sur la position ON et que le levier de vitesses est engagé sur D (conduite) ou R (marche arrière). Pou ...

    System
    System Description Chassis control to integrally control the driving system was adopted. Chassis control module inputs the necessary information for control from CAN communication and each switch and integrally controls each system. Refer to the following table for systems controlled a ...