Nissan Rogue (T33) 2021-Present Service Manual: Symptom Diagnosis :: Id Registration Cannot Be Completed

Nissan Rogue (T33) 2021-Present Service Manual / Suspension :: Road Wheels & Tires / Symptom Diagnosis :: Id Registration Cannot Be Completed

Description

The ID of the tire pressure sensor installed in each wheel cannot be registered in the tire pressure monitoring system. Inspect the tire pressure sensor or the tire pressure monitoring system circuit.

Diagnosis Procedure

NOTE:

The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.

  • Activate and display TPMS sensor IDs

  • Display tire pressure reported by the TPMS sensor

  • Read TPMS DTCs

  • Register TPMS sensor IDs

CHECK TIRE PRESSURE SENSOR INSTALLATION

Check visually that tire pressure sensors are installed to each wheels correctly.

NOTE:

In the following case, TPMS does not function.

  • Tire pressure sensor(s) are not installed.

  • Tire pressure sensor(s) of other cars are installed.

Are the genuine NISSAN tire pressure sensors are installed correctly?

YES>>

GO TO 2.

NO>>

Replace and/or Install tire pressure sensor(s).Refer to Removal & Installation. GO TO 3.

CHECK TIRE PRESSURE SENSOR ACTIVATION TOOL

Check tire pressure sensor activation tool.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace the battery of tire pressure sensor activation tool or repair/replace the tire pressure sensor activation tool.

TIRE PRESSURE SENSOR ID REGISTRATION

Perform tire pressure sensor ID registration. Refer to Description.

CAUTION:

To perform ID registration, observe the following points:

  • Never register ID in a place where radio waves are interfered (e.g. radio tower).

  • Never register ID in a place close to Nissan Ariya vehicles including TPMS.

Is tire pressure sensor ID registration completed?

YES>>

Inspection End.

NO>>

GO TO 4.

CHECK TIRE PRESSURE SIGNAL

Change the work location and perform ID registration again.

NOTE:

Depending on the tire pressure sensor position*, a blind spot exists, and the tire pressure receiver gets a poor reception. If an ID registration is performed under this condition, the registration may not be completed. In such case, follow the instructions below to improve the radio wave receiving environment.

  • Rotate tire by 90°, 180°, or 270°. (This step is to change tire pressure sensor position.)

  • Open the door close to the tire of which ID registration is ongoing.

*: Radio wave reception condition depends on Nissan Ariya vehicle architecture (e.g. body harness layout, tire wheel design) or environment.

When ID registration is performed, which wheels do not react?

All wheels react and ID registration is possible.>>

Inspection End.

Only certain wheel(s) do not react.>>

Replace applicable tire pressure sensor. Refer to Removal & Installation.

All wheels do not react.>>

Replace the BCM. Refer to Removal and Installation.

    Symptom Diagnosis. Low Tire Pressure Location Indicator Continues Displaying
    Description The low tire pressure location indicator continues displaying though low tire pressure warning lamp turns/stays OFF. Diagnosis Procedure CHECK TIRE PRESSURE Ignition...
    Symptom Diagnosis. Easy Fill Tire Alert Does Not Activate
    Description The easy fill tire alert does not function while inflating a tire when the CVT shift selector position is in P-range with the ignition switch ON or with the engine s...

    Other materials:

    Automatic Emergency Braking. Ecu Diagnosis Information
    Adas Control Unit 2 List of ECU Reference ECU Reference ADAS control unit 2 (Without ProPILOT Assist 2.1) Reference Value Fail-safe (ADAS Control Unit 2) DTC Inspection Priority Chart DTC Index ADAS control unit 2 (With ProPILOT Assist 2.1) Reference Value Fail- ...

    Vehicle information display warnings and indicators
    Engine start operation indicator This indicator appears when the shift position is set to P (Park). It informs the driver that the engine will start when the ignition switch is pushed while depressing the brake pedal. The Nissan Rogue engine can be started directly in any ignition switch position. ...

    Lane Change Assist
    Basic information Lane Change Assist is a feature of ProPILOT Assist 2.1 on the Nissan Rogue. Read the entire ProPILOT Assist section before using this system, including how to operate it and how to interpret the display. When ProPILOT Assist is active and the status indicator A is illuminated in ...