Nissan Rogue (T33) 2021-Present Service Manual: Steering Switch Signal a Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Information & Multimedia :: Meter, Warning Lamp & Indicator / Type B :: Dtc/circuit Diagnosis / Steering Switch Signal a Circuit

Component Function Check

CHECK COMBINATION METER INPUT SIGNAL

CONSULT

  1. Ignition switch ON.

  2. Select “Steering switch input” in “Data monitor” mode of “M&A”.

  3. Check that the function operates normally according to the following conditions:

Condition Value
CONTROL switch is pressed SW1
Jog dial is rotated to upward SW2
Jog dial is rotated to downward SW3
OK switch is pressed SW4
LEFT/BACK switch is pressed SW5
RIGHT switch is pressed SW6
VOL DOWN switch is pressed SW7
VOL UP switch is pressed SW8
TEL END switch is pressed SW9
VR/TEL switch is pressed SW10
SEEK DOWN switch is pressed SW11
SEEK UP switch is pressed SW12
Other than above NO INPUT

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

The steering switch has a built-in CPU. Details for refer to Steering Switch.

CHECK FUSE

Check that the fuse is not blown:

Unit Location Fuse No. Capacity
Steering switches Fuse block (J/B) 40 10 A

Is the fuse blown?

YES>>

Replace the blown fuse after repairing the affected circuit.

NO>>

GO TO 2.

CHECK STEERING SWITCH POWER SUPPLY CIRCUIT

  1. Ignition switch ON.

  2. Check voltage between spiral cable harness connector and ground.

    Terminals Ignition switch position

    Voltage

    (Approx.)
    (+) (−)
    Spiral cable Ground
    Connector Terminal
    M30 16 ACC or ON Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair harness or connector.

CHECK STEERING SWITCH GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect spiral cable harness connector.

  3. Check continuity between spiral cable harness connector and ground.

    Spiral cable Ground Continuity
    Connector Terminal
    M30 15 Yes

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair harness or connector.

CHECK STEERING SWITCH SIGNAL A CIRCUIT

  1. Disconnect combination meter harness connector.

  2. Check continuity between combination meter harness connector and spiral cable harness connector.

    Combination meter Spiral cable Continuity
    Connector Terminal Connector Terminal
    M76 33 M30 13 Yes

  3. Check continuity between combination meter harness connector and ground.

    Combination meter Ground Continuity
    Connector Terminal
    M76 33 No

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair harness or connector.

CHECK STEERING SWITCH SIGNAL GROUND CIRCUIT

  1. Check continuity between combination meter harness connector and spiral cable harness connector.

    Combination meter Spiral cable Continuity
    Connector Terminal Connector Terminal
    M76 34 M30 11 Yes

  2. Check continuity between combination meter harness connector and ground.

    Combination meter Ground Continuity
    Connector Terminal
    M76 34 No

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair harness or connector.

CHECK SPIRAL CABLE

  1. Disconnect spiral cable harness connectors.

  2. Check continuity between spiral cable harness connectors.

    Spiral cable Continuity
    Connector Terminal Connector Terminal
    M154 22 M30 16 Yes
    29 15
    27 13
    25 11

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Replace spiral cable. Refer to Removal and Installation.

CHECK STEERING SWITCH

Check steering switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace steering switches. Refer to Removal and Installation.

    Meter Speaker Signal Circuit
    Diagnosis Procedure CHECK METER SPEAKER CIRCUIT FOR OPEN Ignition switch OFF. Disconnect combination meter harness connector and meter speaker harness connector. Check the conti...
    Steering Switch Signal B Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL CONSULT Ignition switch ON. Select “Steering switch input” in “Data monitor” mode of “M&A”. Check t...

    Other materials:

    P00fe Evap Control System
    DTC Description This diagnosis detects clogs in the EVAP line between fuel tank and EVAP canister purge volume control solenoid valve.ECM controls EVAP control system as below. ECM monitors EVAP line pressure change to diagnose if there is no clogging between EVAP canister and fuel tank. E ...

    Basic Inspection. Tire Pressure Sensor Id Registration
    Description This procedure must be performed. After replacement of a tire pressure sensor or BCM. After replacement of tire or road wheel. NOTE: ID registration is unnecessary if there are no change in the positions of each wheels (tire pressure sensors) before wheel removal and after ...

    Fuel Injector Relay
    Component Inspection CHECK FUEL INJECTOR RELAY Turn ignition switch OFF. Remove fuel injector relay. Refer to Component Parts Location. Check the continuity between fuel injector relay terminals as per the following conditions. Fuel injector relay Condition Continuity + − ...