Nissan Rogue (T33) 2021-Present Service Manual: Removal/replacement of Rear Brake Pad or Rear Brake Caliper

Nissan Rogue (T33) 2021-Present Service Manual / Brakes :: Brake Control System / With Vdc :: Basic Inspection / Removal/replacement of Rear Brake Pad or Rear Brake Caliper

Description

CAUTION:

When performing the following operations, always use CONSULT, for performing “START BRAKE PAD REPLACEMENT”, “FINISH BRAKE PAD REPLACEMENT”, “INITIALIZATION POSITION ADJUSTMENT” of “Work support”. Refer to Work Procedure.

×: Required —: not required

Procedure

  • START BRAKE PAD REPLACEMENT

  • FINISH BRAKE PAD REPLACEMENT

  • INITIALIZATION POSITION ADJUSTMENT

Removing/installing ABS actuator and electric unit (control unit) —
Replacing ABS actuator and electric unit (control unit) —
Removing/installing rear brake pad (When not pressing piston of rear brake caliper assembly) —
Removing/installing rear brake pad (When pressing piston of rear brake caliper assembly) ×
Replacing rear brake pad ×
Removing/installing rear brake caliper assembly —
Replacing rear brake caliper assembly ×
Removing/installing parking brake switch —
Replacing parking brake switch —
Replacing/removing/installing rear disc rotor —

Work Procedure

BEFORE REMOVAL/REPLACEMENT OF REAR BRAKE PAD OR REAR CALIPER ASSEMBLY

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF) to ON.

    CAUTION:

    Never start the engine.

  2. Select “ABS”, “Work support”, and “START BRAKE PAD REPLACEMENT” according to this order.

    CAUTION:

    • Never operate the parking brake switch.

    • Never depress the brake pedal.

  3. Touch “START”.

>>

GO TO 2.

REMOVAL AND INSTALLATION/REPLACEMENT OF REAR BRAKE PAD OR REAR BRAKE CALIPER ASSEMBLY

Replace the rear brake pad or rear brake caliper.

  • Rear brake pad: Refer to Removal and Installation.

  • Rear brake caliper assembly: Refer to Removal and Installation.

>>

GO TO 3.

AFTER INSTALLATION/REPLACEMENT OF REAR BRAKE PAD OR REAR CALIPER ASSEMBLY

CONSULT

  1. Select “ABS”, “Work support”, and “FINISH BRAKE PAD REPLACEMENT” according to this order.

    CAUTION:

    • Never operate the parking brake switch.

    • Never depress the brake pedal.

  2. Touch “START”.

>>

GO TO 4.

PERFORM INITIALIZATION POSITION ADJUSTMENT

CONSULT

  1. Select “ABS”, “Work support”, and “INITIALIZATION POSITION ADJUSTMENT” according to this order.

    CAUTION:

    • Never operate the parking brake switch.

    • Never depress the brake pedal.

  2. Touch “START”.

>>

GO TO 5.

PERFORM THE SELF-DIAGNOSIS

CONSULT

  1. Pull parking brake switch to activate electric parking brake.

  2. Push parking brake switch to release electric parking brake.

  3. Perform self-diagnosis for “ABS”.

Is malfunction detected?

YES>>

Check the DTC. Refer to DTC Index. GO TO 6.

NO>>

GO TO 6.

CHECK Data monitor

CONSULT

Select “ABS”, “Data monitor”, “BR FORCE EST (LH)” and “BR FORCE EST (RH)” according to this order. Check that signals are within the specified value. Refer to Reference Value.

Is the check result normal?

YES>>

GO TO 7.

NO>>

GO TO 1.

ERASE SELF-DIAGNOSIS MEMORY

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF) to ON.

  2. Erase self-diagnosis results memory of “ABS”.

Is the memory erased?

YES>>

Inspection End

NO>>

Check the items indicated by the self-diagnosis.

    Adjustment of Brake Caliper Initial Position
    Description CAUTION: When performing the following operations, always use CONSULT (It cannot be performed by any means other than CONSULT.), for performing "INITIALIZATION POSIT...
    Change of System Mode
    Description CAUTION: When the following operations are performed, always use CONSULT, for performing “SYSTEM MODE CHANGE” of “WORK SUPPORT”. Refer to Work Procedure. ×:...

    Other materials:

    Front Blower Motor
    Diagnosis Procedure CHECK FUSE Ignition switch OFF. Check that the following fusible link are not blown (open). Unit Location Fuse No. Capacity Front blower motor Fuse block (J/B) LL 40 A Is the fuses blown (open)? YES>> Replace the blown (open) fusib ...

    Manifold Absolute Pressure (map) Sensor
    Component Inspection CHECK MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR Turn ignition switch OFF. Remove manifold absolute pressure (MAP) sensor with its harness connector. Install pressure pump (A) to manifold absolute pressure (MAP) sensor. CAUTION: When insert a pressure pump hose ...

    Air Breather Hose
    Exploded View 1. Transaxle assembly 2. Air breather hose 3. Air breather tube Removal and Installation REMOVALRemove air duct and air cleaner. Refer to Removal and Installation. Remove air breather hose (1). INSTALLATIONInstallation is in the reverse order of removal.CAUT ...