Nissan Rogue (T33) 2021-Present Service Manual: Push-Button Ignition Switch Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Power Control System / Power Distribution System :: Dtc/circuit Diagnosis / Push-Button Ignition Switch Circuit

Component Function Check

CHECK FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “Push switch” in “Data monitor” mode of “INTELLIGENT KEY”.

  3. Check the push-button ignition switch signal under the following conditions:

Monitor item Condition Status
Push switch Push-button ignition switch is pressed On
Push-button ignition switch is not pressed Off

Is the inspection result normal?

YES>>

Push-button ignition switch circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK PUSH-BUTTON IGNITION SWITCH SIGNAL OUTPUT VOLTAGE

  1. Ignition switch OFF.

  2. Disconnect push-button ignition switch connector.

  3. Check voltage between push-button ignition switch harness connector and ground.

    + -

    Voltage

    (Approx.)
    Push-button ignition switch
    Connector Terminal
    M17 8 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 2.

CHECK PUSH-BUTTON IGNITION SWITCH SIGNAL CIRCUIT (OPEN)

  1. Disconnect Intelligent Key unit connector.

  2. Check continuity between push-button ignition switch harness connector and Intelligent Key unit harness connector.

    Push-button ignition switch Intelligent Key unit Continuity
    Connector Terminal Connector Terminal
    M17 8 M184 9 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

CHECK PUSH-BUTTON IGNITION SWITCH SIGNAL CIRCUIT (SHORT TO GROUND)

Check continuity between push-button ignition switch harness connector and ground.

Push-button ignition switch — Continuity
Connector Terminal
M17 8 Ground No

Is the inspection result normal?

YES>>

Replace Intelligent Key unit. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

CHECK PUSH-BUTTON IGNITION SWITCH GROUND CIRCUIT (OPEN)

Check continuity between push-button ignition switch harness connector and ground.

Push-button ignition switch — Continuity
Connector Terminal
M17 4 Ground Yes

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair the harness or connector.

CHECK PUSH-BUTTON IGNITION SWITCH

Check push-button ignition switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace push-button ignition switch. Refer to Removal and Installation.

Component Inspection

CHECK PUSH-BUTTON IGNITION SWITCH

  1. Ignition switch OFF.

  2. Disconnect push-button ignition switch connector.

  3. Check continuity between push-button ignition switch terminals.

    Push-button ignition switch Condition Continuity
    Terminal
    8 4 Pressed Yes
    Not pressed No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace push-button ignition switch. Refer to Removal and Installation.

    Accessory Relay
    Diagnosis Procedure CHECK ACCESSORY RELAY POWER SUPPLY Disconnect accessory relay connector. Check voltage between accessory relay harness connector and ground. (+) (–) Voltag...
    Power Distribution System. Symptom Diagnosis. Push-Button Ignition Switch Does Not Operate
    Push-Button Ignition Switch Does Not Operate Diagnosis Procedure DescriptionCheck that vehicle is under the condition shown in “Conditions of vehicle” before starting diagno...

    Other materials:

    System Description. Component Parts
    Component Parts Location A. Steering gear assembly (Without ProPILOT Assist 2.1) B. Steering gear assembly (With ProPILOT Assist 2.1) No.Component 1. ABS actuator and electric unit (control unit) Refer to Component Parts Location for detailed installation location. 2. ECM Refer t ...

    Dtc/circuit Diagnosis. B2428-44 Automatic Back Door Control Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2428-44 Automatic back door control unit (Automatic back door control unit) Diagnosis condition All times Signal (terminal) — Threshold Automatic ...

    Engine Cover
    Exploded View Engine cover Stud Bracket Bracket         : N·m (kg-m, in-lb) Removal and Installation REMOVALRemove the engine cover by pulling it off in an upwards direction.CAUTION: Never damage or scratch engine cover when installing or ...