Nissan Rogue (T33) 2021-Present Service Manual: P34ae Electric Intake Valve Timing Control Position Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P34ae Electric Intake Valve Timing Control Position Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P34AE 00

A camshaft posi actuator posi sens B1

(A Camshaft Position Actuator Position Sensor A Circuit Low Bank 1) 		Diagnosis condition —
Signal (terminal) Electric intake valve timing control position sensor signal
Threshold An excessively low voltage from the sensor is sent to the electric intake valve timing (IVT) control module.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors [Electric intake valve timing (IVT) control actuator circuit is open or shorted.]

  • Electric IVT control actuator

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited.

When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Maintaining engine speed at more than 2000 rpm for at least 1 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ELECTRIC INTAKE VALVE TIMING CONTROL POSITION SENSOR CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect electric intake valve timing control position sensor harness connector.

  3. Disconnect electric intake valve timing control module harness connector.

  4. Check the continuity between the electric intake valve timing control position sensor harness connector and the electric intake valve timing control module harness connector.

    Electric intake valve timing control position sensor Electric intake valve timing control module Continuity
    Connector Terminal Connector Terminal
    F92 3 F113 9 Existed
    4 35
    5 6

  5. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

Replace electric intake valve timing control actuator. Refer to Exploded View.

NO>>

Repair or replace error-detected parts.

    P34ad Electric Intake Valve Timing Control Actuator
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P34AD 00 A camshaft posi actuator posi sens B1 (A Camshaft Posit...
    P34af Electric Intake Valve Timing Control Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P34AF 00 A camshaft posi actuator posi sens B1 (A camshaft posit...

    Other materials:

    Diagnosis System (hvac)
    CONSULT Function CONSULT performs the following functions via CAN communication with A/C amp. Diagnosis mode Function Self diagnosis result Display non-network DTC which A/C amp. memorizes ECU identification The A/C amp. part number is displayed Active Test The signals used t ...

    U0076-00 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U0076 00 Control module communication Bus D Off Diagnosis condition When ignition switch is ON. Signal (terminal) CAN communication signal Threshold Not transmitting. Diagn ...

    Dtc/circuit Diagnosis. Drive Mode Select Switch Circuit
    Diagnosis Procedure CHECK DRIVE MODE SELECT SWITCH SIGNAL CIRCUIT Ignition switch OFF. Disconnect drive mode select switch harness connector and BCM harness connector. Check the continuity between drive mode select switch harness connector and BCM harness connector. 2WD models with ...