Nissan Rogue (T33) 2021-Present Service Manual: P34af Electric Intake Valve Timing Control Position Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P34af Electric Intake Valve Timing Control Position Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P34AF 00

A camshaft posi actuator posi sens B1

(A camshaft position actuator position sensor A circuit high Bank 1) 		Diagnosis condition —
Signal (terminal) Electric intake valve timing control position sensor signal
Threshold An excessively high voltage from the sensor is sent to the electric IVT control module
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

  • Harness or connectors [Electric intake valve timing (IVT) control actuator circuit is open or shorted.]

  • Electric IVT control actuator (motor 1 hall sensor)

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited.

When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Maintaining engine speed at more than 2000 rpm for at least 1 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ELECTRIC INTAKE VALVE TIMING (IVT) CONTROL POSITION SENSOR CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect electric IVT control position sensor harness connector.

  3. Disconnect electric IVT control module harness connector.

  4. Check the continuity between electric IVT control position sensor harness connector and electric IVT control module harness connector.

    Electric IVT control position sensor Electric IVT control module Continuity
    Connector Terminal Connector Terminal
    F92 3 F113 9 Existed
    4 35
    5 6

  5. Check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 2

NO>>

Repair or replace error-detected parts.

CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

Replace electric IVT control actuator. Refer to Exploded View.

NO>>

Repair or replace error-detected parts.

    P34ae Electric Intake Valve Timing Control Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P34AE 00 A camshaft posi actuator posi sens B1 (A Camshaft Posit...
    P34c8 Electric Intake Valve Timing Control Module
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P34C8 00 Camshaft position control module (Camshaft position con...

    Other materials:

    P0090 Frp System
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0090 00 FUEL PUMP (Fuel Pressure Regulator "A" Control Circuit/Open) Diagnosis condition Engine running at idle Signal (terminal) High pressure fuel p ...

    Removal and Installation. Automatic Back Door Control Unit
    Removal and Installation REMOVALRemove luggage side lower finisher LH. Refer to Removal and Installation. Disconnect automatic back door control unit harness connector. Remove the automatic back door control unit mounting nuts (A), and then remove the automatic back door control unit (1). INST ...

    System
    Can Communication System System Description SYSTEM DIAGRAM With type B meter With type A meter Without ProPILOT Assist 2.1 With type A meter With ProPILOT Assist 2.1 DESCRIPTION CAN (Controller Area Network) is a serial communication line for real time application. It ...