Nissan Rogue (T33) 2021-Present Service Manual: P34ad Electric Intake Valve Timing Control Actuator

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P34ad Electric Intake Valve Timing Control Actuator

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P34AD 00

A camshaft posi actuator posi sens B1

(A Camshaft Position Actuator Position Sensor A Range/Performance Bank 1) 		Diagnosis condition —
Signal (terminal)

  • Electric intake valve timing control position sensor signal

  • Intake camshaft position sensor (electric intake valve timing control ) signal
Threshold The correlation between position signal and phase signal of electric intake valve timing control actuator motor is incorrect.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors [Electric intake valve timing (IVT) control actuator circuit is open or shorted.]

  • Electric IVT control actuator

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited.

When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Maintaining engine speed at more than 2000 rpm for at least 1 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ELECTRIC INTAKE VALVE TIMING CONTROL POSITION SENSOR CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect electric intake valve timing control position sensor harness connector.

  3. Disconnect electric intake valve timing control module harness connector.

  4. Check the continuity between the electric intake valve timing control position sensor harness connector and the electric intake valve timing control module harness connector.

    Electric intake valve timing control position sensor Electric intake valve timing control module Continuity
    Connector Terminal Connector Terminal
    F92 3 F113 9 Existed
    4 35
    5 6

  5. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

Replace the electric intake valve timing control actuator. Refer to Exploded View.

NO>>

Repair or replace error-detected parts.

    P34ac Electric Intake Valve Timing Control Actuator
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P34AC 00 A camshaft posi actuator posi sens B1 (A Camshaft Posit...
    P34ae Electric Intake Valve Timing Control Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P34AE 00 A camshaft posi actuator posi sens B1 (A Camshaft Posit...

    Other materials:

    Symptom Diagnosis. Low Tire Pressure Warning Lamp Does Not Turn Off
    Description The low tire pressure warning lamp does not turn OFF after several seconds is passed after engine starts. Diagnosis Procedure CHECK TIRE PRESSURE Ignition switch ON. CAUTION: Never start the engine. Check the tire pressure for all wheels and adjust to the specified value ...

    Preparation
    Special Service Tools The actual shapes of TechMate tools may differ from those of special service tools illustrated here. Tool number (TechMate No.) Tool name Description (NI-39570) Chassis ear Locates the noise (NI-50397) NISSAN Squeak and Rattle Kit Repairs the ...

    Basic Inspection. Additional Service When Replacing Ecm
    Description Performing the following procedure can automatically activate recommunication of ECM and Intelligent Key unit, but only when the ECM is replaced with a new one*. For details, refer to Work Procedure.*: New one means a virgin ECM that has never been energized on-board.(In this step, ...