Nissan Rogue (T33) 2021-Present Service Manual: Illumination Control Switch Signal Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Information & Multimedia :: Meter, Warning Lamp & Indicator / Type a :: Dtc/circuit Diagnosis / Illumination Control Switch Signal Circuit

Component Function Check

CHECK COMBINATION METER INPUT SIGNAL

  1. Ignition switch ON.

  2. Measure voltage between the following terminals of the combination meter.

    Combination meter Condition

    Voltage

    (Approx.)
    Connector Terminals
    (+) (−)

    M73 (U.S.A. production)

    M77 (Japan production)     		25 32 When illumination control switch (+) is pressed 0 V
    Other than the above 5.0 V
    31 When illumination control switch (−) is pressed 0 V
    Other than the above 5.0 V

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK ILLUMINATION CONTROL SWITCH SIGNAL CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect combination meter harness connector and illumination switch harness connector.

  3. Check continuity between combination meter harness connector and illumination control switch harness connector.

    Combination meter Illumination control switch Continuity
    Connector Terminal Connector Terminal

    M73 (U.S.A. production)

    M77 (Japan production)     		32 M3 4 Yes
    31 7
    25 6

  4. Check continuity between combination meter harness connector and ground.

    Combination meter — Continuity
    Connector Terminal

    M73 (U.S.A. production)

    M77 (Japan production)     		32 Ground No
    31
    25

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair harness or connector.

CHECK ILLUMINATION CONTROL SWITCH

Check illumination control switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Replace illumination control switch. Refer to Removal and Installation.

Component Inspection

CHECK ILLUMINATION CONTROL SWITCH

  1. Ignition switch OFF.

  2. Disconnect illumination control switch connector.

  3. Check continuity between the following terminals of the illumination control switch.

    Terminals Condition Continuity
    Illumination control switch
    6 4 When illumination control switch (+) is pressed Yes
    Other than the above No
    7 When illumination control switch (−) is pressed Yes
    Other than the above No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace illumination control switch. Refer to Removal and Installation.

    Steering Switch Signal B Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL CONSULT Ignition switch ON. Select “Steering switch input” in “Data monitor” mode of “M&A”. Check t...
    Fuel Level Sensor Signal Circuit
    Component Function Check PERFORM COMPONENT FUNCTION CHECK (1) Ignition switch OFF. Disconnect fuel level sensor unit, fuel pump and FPCM (fuel level sensor) (main) harness conne...

    Other materials:

    P00fe Evap Control System
    DTC Description This diagnosis detects clogs in the EVAP line between fuel tank and EVAP canister purge volume control solenoid valve.ECM controls EVAP control system as below. ECM monitors EVAP line pressure change to diagnose if there is no clogging between EVAP canister and fuel tank. E ...

    B20c7-15 A/c Clutch
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B20C7–15 A/C clutch (A/C clutch) [CIRC SHORT TO BATT OR OPEN] Diagnosis condition When A/C switch is ON Signal (Terminal) Magnetic clutch ON signal ...

    Tire chains
    WARNING If tire chains are used on the Nissan Rogue, ensure they provide adequate clearance from suspension and body components. Incorrect chain selection or improper installation can cause damage to brakes, suspension or other components, risking a crash. Use only the recommended chains or an app ...