Nissan Rogue (T33) 2021-Present Service Manual: P11b0 Vcr Target Angle (cold Start)

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P11b0 Vcr Target Angle (cold Start)

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P11B0 00

VCR target angle (cold start)

[Variable compression ratio target angle (cold start)] 		Diagnosis condition Engine cold start
Signal (terminal) —
Threshold There is a gap between angle of target and phase-control angle degree (High compression ratio)
Diagnosis delay time 110 seconds or more

POSSIBLE CAUSE

  • VCR actuator

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC P11B0 is displayed with the following DTC, perform the confirmation procedure (trouble diagnosis) for the applicable DTC.

Is DTC P11A0, P11A1, P11A2, P11A3 P11A4, P11A6, P11A7, P11AB, P11AC, P11AD, P11AE or P11AF detected?

YES>>

Perform diagnosis of applicable.

  • DTC P11A0: DTC Description.

  • DTC P11A1: DTC Description.

  • DTC P11A2: DTC Description.

  • DTC P11A3: DTC Description.

  • DTC P11A4: DTC Description.

  • DTC P11A6: DTC Description.

  • DTC P11A7: DTC Description.

  • DTC P11AB: DTC Description.

  • DTC P11AC: DTC Description.

  • DTC P11AD: DTC Description.

  • DTC P11AE: DTC Description.

  • DTC P11AF: DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

  1. Ignition switch OFF and wait at least 10 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 12 V or more with ignition switch ON.

YES>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 110 seconds.

  2. Check 1st trip DTC.

Is DTC P11B0 detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P11B0 is displayed with the following DTC, perform the confirmation procedure (trouble diagnosis) for the applicable DTC.

Is DTC P11A0, P11A1, P11A2, P11A3 P11A4, P11A6, P11A7, P11AB, P11AC, P11AD, P11AE or P11AF detected?

YES>>

Perform diagnosis of applicable.

  • DTC P11A0: DTC Description.

  • DTC P11A1: DTC Description.

  • DTC P11A2: DTC Description.

  • DTC P11A3: DTC Description.

  • DTC P11A4: DTC Description.

  • DTC P11A6: DTC Description.

  • DTC P11A7: DTC Description.

  • DTC P11AB: DTC Description.

  • DTC P11AC: DTC Description.

  • DTC P11AD: DTC Description.

  • DTC P11AE: DTC Description.

  • DTC P11AF: DTC Description.

NO>>

GO TO 2.

CHECK VCR MOTOR

Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace VCR actuator. Refer to Removal and Installation.

    P11af Vcr Shaft 2 Rotation Angle Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11AF 00 VCR shaft 2 rotation angle sensor (Variable compression...
    P11b1 Vcr Target Angle (cold Start)
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11B1 00 VCR target angle (cold start) [Variable compression rat...

    Other materials:

    Basic information
    WARNING Always confirm the liftgate of the Nissan Rogue is securely closed before driving. Never drive with the liftgate open to prevent exhaust gases from entering the cabin. Do not leave children, pets, or dependent persons inside the Nissan Rogue unattended. Keep hands and feet clear of the ...

    Symptom Diagnosis. Ign Off Interlock Door Unlock Function Does Not Operate
    Diagnosis Procedure CHECK “AUTO DOOR UNLOCK” SETTING IN COMBINATION METER Check “Auto Door Unlock” setting is “IGN OFF”. Is the inspection result normal? YES>> GO TO 2. NO>> Set “IGN OFF” in combination meter. REPLACE BCM Replace BCM. Refer to Removal and I ...

    Removal and Installation. Fillet Molding
    Exploded View 1. Front fillet molding 2. Rear fillet molding front 3. Rear fillet molding rear 4. Grommet — — — — : Clip : Pawl : Nissan Ariya Vehicle front Front Fillet Molding Removal and Installation REMOVALRemove front fille ...