Nissan Rogue (T33) 2021-Present Service Manual: P11af Vcr Shaft 2 Rotation Angle Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P11af Vcr Shaft 2 Rotation Angle Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P11AF 00

VCR shaft 2 rotation angle sensor

(Variable compression ratio shaft 2 rotation angle sensor) 		Diagnosis condition —
Signal (terminal) VCR control shaft 2 rotation angle sensor signal
Threshold The output is abnormal of VCR control shaft 2 rotation angle sensor (S1, S2, S3, S4 , R1, R2 signal)
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (VCR control shaft 2 rotation angle sensor harness connector)

  • VCR actuator (built-in VCR control shaft 2 rotation angle sensor)

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC P11AF is displayed with the following DTC, perform the confirmation procedure (trouble diagnosis) for the applicable DTC.

Is DTC P11AC, P11AD detected?

YES>>

Perform diagnosis of applicable.

  • DTC P11AC: DTC Description.

  • DTC P11AD: DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 12 V or more with ignition switch ON.

YES>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 10 seconds.

  2. Check 1st trip DTC.

Is DTC P11AF detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P11AF is displayed with the following DTC, perform the confirmation procedure (trouble diagnosis) for the applicable DTC.

Is DTC P11AC or P11AD detected?

YES>>

Perform diagnosis of applicable.

  • DTC P11AC: DTC Description.

  • DTC P11AD: DTC Description.

NO>>

GO TO 2.

CHECK VCR CONTROL SHAFT 2 ROTATION ANGLE SENSOR CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect VCR control module and VCR control shaft 2 rotation angle sensor harness connector.

  3. Check the continuity between VCR control module harness connector and VCR control shaft 2 rotation angle sensor harness connector.

    VCR control module VCR control shaft 2 rotation angle sensor Continuity
    Connector Terminal Connector Terminal
    F108 9 F98 2 Existed
    10 5
    12 3
    13 4
    22 1
    23 6

  4. Check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK VCR CONTROL SHAFT 2 ROTATION ANGLE SENSOR

Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace VCR actuator. Refer to Removal and Installation.

    P11ae Vcr Shaft 2 Rotation Angle Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11AE 00 VCR shaft 2 rotation angle sensor (Variable compression...
    P11b0 Vcr Target Angle (cold Start)
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11B0 00 VCR target angle (cold start) [Variable compression rat...

    Other materials:

    System Description. Component Parts. Wiper and Washer System
    Wiper and Washer System Component Parts Location Component Parts Location A. View with washer tank removed from Nissan Ariya vehicle (for USA) B. View with washer tank removed from vehicle C. Behind LH side of front fascia assembly (view with front fascia assembly) removed No. ...

    Removal and Installation. Rear Wiper
    Exploded View Rear wiper motor assembly Pivot seal Rear wiper arm cover Rear wiper arm Rear wiper blade Rear wiper refill : Pawl : N·m (kg-m, in-lb) : N·m (kg-m, ft-lb) Wiper Arm Removal and Installation CAUTION: Clean back door window gla ...

    Basic Inspection. Anti-Pinch Inspection
    Description If any of the following operations are performed, the initialization is necessary for normal operation of anti-pinch function. Refer to Work Procedure. When front power window motor (driver side) replaced. Power supply to the front power window motor (driver side) is not cut ...