Nissan Rogue (T33) 2021-Present Service Manual: P11ae Vcr Shaft 2 Rotation Angle Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P11ae Vcr Shaft 2 Rotation Angle Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P11AE 00

VCR shaft 2 rotation angle sensor

(Variable compression ratio shaft 2 rotation angle sensor) 		Diagnosis condition Ignition switch ON
Signal (terminal) VCR shaft 2 resolver signal
Threshold Range outside of the VCR shaft 2 resolver signal
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (VCR actuator harness connector)

  • VCR actuator

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC P11AE is displayed with the following DTC, perform the confirmation procedure (trouble diagnosis) for the applicable DTC.

Is DTC P11A0, P11AC, P11AD or P11AF detected?

YES>>

Perform diagnosis of applicable.

  • DTC P11A0: DTC Description.

  • DTC P11AC: DTC Description.

  • DTC P11AD: DTC Description.

  • DTC P11AF: DTC Description.

NO>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and let it idle at least 1 minutes.

  2. Check 1st trip DTC.

Is DTC P11AE detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

GO TO 3.

CHECK VCR ACTUATOR

With CONSULT

  1. Reconnect VCR control module and VCR actuator harness connector.

  2. Ignition switch ON.

  3. On CONSULT screen, select “ENGINE”>>“Active Test”>>“VCR system”.

Is DTC P11AE detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P11AE is displayed with the following DTC, perform the confirmation procedure (trouble diagnosis) for the applicable DTC.

Is DTC P11A0, P11AC, P11AD or P11AF detected?

YES>>

Perform diagnosis of applicable.

  • DTC P11A0: DTC Description.

  • DTC P11AC: DTC Description.

  • DTC P11AD: DTC Description.

  • DTC P11AF: DTC Description.

NO>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and let it idle at least 1 minutes.

  2. Check 1st trip DTC.

Is DTC P11AE detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

GO TO 3.

CHECK VCR ACTUATOR

With CONSULT

  1. Reconnect VCR control module and VCR actuator harness connector.

  2. Ignition switch ON.

  3. On CONSULT screen, select “ENGINE”>>“Active Test”>>“VCR system”.

Is the DTC P11AE displayed again?

YES>>

Replace VCR actuator. Refer to Removal and Installation.

NO>>

INSPECTION END

    P11ad Vcr Shaft 2 Rotation Angle Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11AD 00 VCR shaft 2 rotation angle sensor (Variable compression...
    P11af Vcr Shaft 2 Rotation Angle Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11AF 00 VCR shaft 2 rotation angle sensor (Variable compression...

    Other materials:

    Back-Up Lamp Circuit
    Component Function Check CHECK BACK-UP LAMP OPERATION Start the engine. With operating the shift selector, check that the back-up lamp is turned ON. Shift selector position: R range : Back-up lamp ON Shift selector position: Other than above : Back-up lamp OFF Is th ...

    Removal and Installation. Rear Seat Belt
    Exploded View 1. Anchor bolt 2. Seat belt pre-tensioner retractor RH 3. Seat belt hook RH 4. Anchor plate RH 5. Retaining washer 6. Anchor plate LH 7. Seat belt hook LH 8. Seat belt pre-tensioner retractor LH 9. Shoulder bracket RH 10. ...

    P2123 App Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2123 00 APP SEN 1/CIRC (Throttle/Pedal position sensor/switch D circuit high) Diagnosis condition Engine running at idle Signal (terminal) Accelerator ...