Nissan Rogue (T33) 2021-Present Service Manual: P11ad Vcr Shaft 2 Rotation Angle Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P11ad Vcr Shaft 2 Rotation Angle Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P11AD 00

VCR shaft 2 rotation angle sensor

(Variable compression ratio shaft 2 rotation angle sensor) 		Diagnosis condition Ignition switch ON
Signal (terminal) VCR control shaft 2 rotation angle sensor signal
Threshold An excessively low voltage from the VCR control shaft 2 rotation angle sensor is sent to VCR control module.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (VCR control shaft 2 rotation angle sensor harness connector)

  • VCR actuator (built-in VCR control shaft 2 rotation angle sensor)

  • VCR control module

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC P11AD is displayed with the following DTC, perform the confirmation procedure (trouble diagnosis) for the applicable DTC.

Is DTC P11A0 detected?

YES>>

Perform diagnosis of applicable. DTC P11A0: DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

  1. Ignition switch OFF and wait at least 10 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 12 V or more with ignition switch ON.

YES>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Ignition switch ON and wait at least 10 seconds.

  2. Check 1st trip DTC.

Is DTC P11AD detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P11AD is displayed with the DTC P10A0, perform the confirmation procedure (trouble diagnosis) for the DTC P10A0.

Is DTC P10A0 detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

CHECK VCR CONTROL SHAFT 2 ROTATION ANGLE SENSOR CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect VCR control module and VCR control shaft 2 rotation angle sensor harness connector.

  3. Check the continuity between VCR control module harness connector and VCR control shaft 2 rotation angle sensor harness connector.

    VCR control module VCR control shaft 2 rotation angle sensor Continuity
    Connector Terminal Connector Terminal
    F108 9 F98 2 Existed
    10 5
    12 3
    13 4
    22 1
    23 6

  4. Check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK VCR CONTROL SHAFT 2 ROTATION ANGLE SENSOR

Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace VCR actuator. Refer to Removal and Installation.

    P11ac Vcr Shaft 2 Rotation Angle Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11AC 00 VCR shaft 2 rotation angle sensor (Variable compression...
    P11ae Vcr Shaft 2 Rotation Angle Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11AE 00 VCR shaft 2 rotation angle sensor (Variable compression...

    Other materials:

    Camshaft
    Exploded View 1. Intake camshaft position sensor 2. Exhaust camshaft position sensor 3. O-ring 4. Camshaft bracket 5. Camshaft (EXH) 6. Dowel pin 7. Camshaft bearing 8. Camshaft sprocket (EXH) 9. Camshaft sprocket (INT) 10. Valve lifte ...

    Back-Up Lamp Circuit
    Component Function Check CHECK BACK-UP LAMP OPERATION Start the engine. With operating the shift selector, check that the back-up lamp is turned ON. Shift selector position: R range : Back-up lamp ON Shift selector position: Other than above : Back-up lamp OFF Is th ...

    Operation
    Head up Display Switch Name and Function Head Up Display SwitchNo.Switch nameDescription Head Up Display switch To turn the Head Up Display on, press the Head Up Display switch during ignition switch ON To turn the Head Up Display off, press the Head Up Display switch NOTE: ...