Nissan Rogue (T33) 2021-Present Service Manual: Back-Up Lamp Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Exterior Lighting System / Led Headlamp :: Dtc/circuit Diagnosis / Back-Up Lamp Circuit

Component Function Check

CHECK BACK-UP LAMP OPERATION

  1. Start the engine.

  2. With operating the shift selector, check that the back-up lamp is turned ON.

    Shift selector position: R range : Back-up lamp ON
    Shift selector position: Other than above : Back-up lamp OFF

Is the inspection result normal?

YES>>

Back-up lamp circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK BACK-UP LAMP BULB

  1. Ignition switch OFF.

  2. Check the back-up lamp bulb.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace the corresponding rear combination lamp (back door side) bulb. Refer to Replacement.

CHECK BACK-UP LAMP RELAY FUSE

Check that the following fuse is not blown (open):

Unit Location Fuse No. Capacity
Ignition switch power supply IPDM E/R 71 10 A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 3.

CHECK BACK-UP LAMP RELAY POWER SUPPLY

  1. Ignition switch ON.

  2. Check voltage between IPDM E/R harness connector and ground.

    + -

    Voltage

    (Approx.)
    IPDM E/R
    Connector Terminal
    E217 55 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace IPDM E/R. Refer to Removal and Installation.

CHECK BACK-UP LAMP RELAY POWER SUPPLY CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R connector and back-up lamp relay connector.

  3. Check continuity between IPDM E/R harness connector and back-up lamp relay harness connector.

    IPDM E/R Back-up lamp relay Continuity
    Connector Terminal Connector Terminal
    E217 55 E80 2 Yes
    3

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness.

CHECK BACK-UP LAMP RELAY

Check back-up lamp relay. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Replace back-up lamp relay.

CHECK BACK-UP LAMP RELAY CONTROL SIGNAL

  1. Connect IPDM E/R connector and back-up lamp relay connector.

  2. Start the engine.

  3. With operating the shift selector, check voltage between BCM harness connector and ground.

    With type A meter
    + - Condition

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    E60 125 Ground Shift selector R range 0 V
    Except R range Battery voltage
    With type B meter
    + - Condition

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    E29 119 Ground Shift selector R range 0 V
    Except R range Battery voltage

Is the inspection result normal?

YES>>

GO TO 8.

NO-1>>

Fixed at 0 V: GO TO 7.

NO-2>>

Fixed at battery voltage: Replace BCM. Refer to Removal and Installation.

CHECK BACK-UP LAMP RELAY CONTROL SIGNAL CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect BCM connector and back-up lamp relay connector.

  3. Check continuity between BCM harness connector and back-up lamp relay harness connector.

    With type A meter
    BCM Back-up lamp relay Continuity
    Connector Terminal Connector Terminal
    E60 125 E80 4 Yes
    With type B meter
    BCM Back-up lamp relay Continuity
    Connector Terminal Connector Terminal
    E29 119 E80 4 Yes

  4. Check continuity between BCM harness connector and ground.

    With type A meter
    BCM — Continuity
    Connector Terminal
    E60 125 Ground No
    With type B meter
    BCM — Continuity
    Connector Terminal
    E29 119 Ground No

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK BACK-UP LAMP POWER SUPPLY CIRCUIT 1

  1. Ignition switch OFF.

  2. Disconnect rear combination lamp (back door side) connector and back-up lamp relay connector.

  3. Check continuity between rear combination lamp (back door side) harness connector and back-up lamp relay harness connector.

    Rear combination lamp (back door side) Back-up lamp relay Continuity
    Connector Terminal Connector Terminal
    RH D519 7 E80 1 Yes
    LH D518

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Repair or replace harness.

CHECK BACK-UP LAMP GROUND CIRCUIT

Check continuity between rear combination lamp (back door side) harness connector and ground.

Rear combination lamp (back door side) — Continuity
Connector Terminal
RH D519 5 Ground Yes
LH D518

Is the inspection result normal?

YES>>

Check corresponding rear combination lamp (back door side) sub harness, if there is a malfunction, repair or replace. If there is no malfunction, replace the corresponding rear combination lamp (back door side) bulb. Refer to Replacement.

NO>>

Repair or replace harness.

Component Inspection

CHECK BACK-UP LAMP RELAY

  1. Ignition switch OFF.

  2. Disconnect back-up lamp relay connector.

  3. Check continuity between back-up lamp relay terminals.

    Back-up lamp relay Condition Continuity
    Terminal
    12 V direct current supply between terminals and . Yes
    No current supply No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace back-up lamp relay.

    Stop Lamp Relay Circuit
    Diagnosis Procedure CHECK STOP LAMP OPERATION Check that stop lamp is turned ON/OFF when the brake pedal is depressed/released. Is the inspection result normal? YES>> GO T...
    Turn Signal Lamp Circuit
    Component Function Check CHECK TURN SIGNAL LAMP OPERATION CONSULT Ignition switch ON. Select “Flasher” in “Active test” mode of “BCM”. With operating the test item, ...

    Other materials:

    Vehicle information display warnings and indicators
    Engine start operation indicator This indicator appears when the shift position is set to P (Park). It informs the driver that the engine will start when the ignition switch is pushed while depressing the brake pedal. The Nissan Rogue engine can be started directly in any ignition switch position. ...

    Precautions on seat belt usage
    Wearing your seat belt correctly — sitting upright, positioned well back in the seat, and keeping both feet on the floor — significantly reduces the risk of injury or death in an accident. When used properly, seat belts work together with your Nissan Rogue’s safety systems, including suppleme ...

    Hill Start Assist system
    WARNING Never rely solely on the Hill Start Assist system to keep the Nissan Rogue from rolling backward on a hill. Always remain attentive, apply the brake pedal when stopped on steep inclines, and use extra caution on icy or muddy slopes. Failure to prevent rollback could result in loss of contr ...