Nissan Rogue (T33) 2021-Present Service Manual: Stop Lamp Relay Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Exterior Lighting System / Led Headlamp :: Dtc/circuit Diagnosis / Stop Lamp Relay Circuit

Diagnosis Procedure

CHECK STOP LAMP OPERATION

Check that stop lamp is turned ON/OFF when the brake pedal is depressed/released.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Check stop lamp circuit. Refer to Component Function Check.

CHECK STOP LAMP RELAY FUSE

Check that the following fuse is not blown (open):

Unit Location Fuse No. Capacity
Ignition switch power supply Fuse and fusible link box 6 116 10 A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 3.

CHECK STOP LAMP RELAY POWER SUPPLY CIRCUIT

  1. Disconnect stop lamp relay connector.

  2. Ignition switch ON.

  3. Check voltage between stop lamp relay harness connector and ground.

    + -

    Voltage

    (Approx.)
    Stop lamp relay
    Connector Terminal
    E148 1 Ground Battery voltage
    3

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK STOP LAMP RELAY

Check stop lamp relay. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace stop lamp relay.

CHECK STOP LAMP RELAY CONTROL SIGNAL CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect chassis control module connector.

  3. Check continuity between chassis control module harness connector and stop lamp relay harness connector.

    Chassis control module Stop lamp relay Continuity
    Connector Terminal Connector Terminal
    M32 32 E148 4 Yes

  4. Check continuity between chassis control module harness connector and ground.

    Chassis control module — Continuity
    Connector Terminal
    E32 32 Ground No

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness.

CHECK STOP LAMP POWER SUPPLY CIRCUIT 1

  1. Disconnect rear combination lamp (body side) connector.

  2. Check continuity between rear combination lamp (body side) harness connector and stop lamp relay harness connector.

    Rear combination lamp (body side) Stop lamp relay Continuity
    Connector Terminal Connector Terminal
    RH B102 3 E148 2 Yes
    LH B90

  3. Check continuity between stop lamp relay harness connector and ground.

    Stop lamp relay — Continuity
    Connector Terminal
    E148 2 Ground No

Is the inspection result normal?

YES>>

Replace chassis control module. Refer to Removal and Installation.

NO>>

Repair or replace harness.

Component Inspection

CHECK STOP LAMP RELAY

  1. Ignition switch OFF.

  2. Disconnect stop lamp relay connector.

  3. Check continuity between stop lamp relay terminals.

    Stop lamp relay Condition Continuity
    Terminal
    12 V direct current supply between terminals and . Yes
    No current supply No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace stop lamp relay.

    Stop Lamp Circuit
    Component Function Check CHECK STOP LAMP OPERATION Ignition switch ON. With operating the brake pedal, check that the stop lamp and high-mounted stop lamp is turned ON. Depresse...
    Back-Up Lamp Circuit
    Component Function Check CHECK BACK-UP LAMP OPERATION Start the engine. With operating the shift selector, check that the back-up lamp is turned ON. Shift selector position: R r...

    Other materials:

    Fuel Pump
    Component Inspection CHECK FUEL PUMP Turn ignition switch OFF. Disconnect “fuel level sensor unit and fuel pump” harness connector. Check the resistance between “fuel level sensor unit and fuel pump” terminals as follows. Fuel level sensor unit and fuel pump Condition Res ...

    Can Fundamental. Basic Inspection. Diagnosis and Repair Work Flow
    Diagnosis and Repair Work Flow Trouble Diagnosis Flow Chart DESCRIPTIONDETAIL OF TROUBLE DIAGNOSIS FLOW CHARTINTERVIEW WITH CUSTOMER Interview with the customer is important to detect the root cause of CAN communication system errors and to understand Nissan Ariya vehicle condition and sympto ...

    Side Radar (front Right) (side Radar Front Rh)
    C1ec0-44 Control Unit DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1EC0 44 Control unit Diagnosis condition When ignition switch is ON. Signal (terminal) — Threshold If side radar front RH ...