Nissan Rogue (T33) 2021-Present Service Manual: Stop Lamp Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Exterior Lighting System / Led Headlamp :: Dtc/circuit Diagnosis / Stop Lamp Circuit

Component Function Check

CHECK STOP LAMP OPERATION

  1. Ignition switch ON.

  2. With operating the brake pedal, check that the stop lamp and high-mounted stop lamp is turned ON.

    Depressed : Stop lamp and high-mounted stop lamp ON
    Fully released : Stop lamp and high-mounted stop lamp OFF

Is the inspection result normal?

YES>>

Stop lamp circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK SYMPTOM

Check symptom (A or B).

Symptom
A Both stop lamps and the high-mounted stop lamp will not turn ON
B Any of the stop lamps and the high-mounted stop lamp will not turn ON

Which symptom is detected?

A>>

GO TO 2.

B>>

GO TO 8.

CHECK FUSE

  1. Ignition switch OFF.

  2. Check if any of the following fuses are not blown:

    Signal name Location Fuse No. Capacity

    • Battery power supply (stop lamp)

    • Battery power supply (stop lamp switch 2)

    		 Fuse block (J/B) 21 10 A
    Ignition power supply (stop lamp switch 1) 32 5 A

Is the fuse blown (open)?

YES>>

Replace the blown fuse after repairing the affected circuit.

NO>>

GO TO 3.

CHECK BATTERY POWER SUPPLY (STOP LAMP)

  1. Disconnect BCM connector.

  2. Check voltage between BCM harness connector and ground.

    With ProPILOT assist 2.1
    + -

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    B124 142 Ground Battery voltage
    Without ProPILOT assist 2.1
    + -

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    B23 139 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK STOP LAMP SWITCH POWER SUPPLY

  1. Disconnect stop lamp switch connector.

  2. Ignition switch ON.

  3. Check voltage between stop lamp switch harness connector and ground.

    + -

    Voltage

    (Approx.)
    Stop lamp switch
    Connector Terminal
    E38 1 Ground Battery voltage
    4

YES>>

GO TO 5.

NO>>

Repair or replace harness.

CHECK STOP LAMP SWITCH SIGNAL

  1. Ignition switch OFF.

  2. Connect stop lamp switch connector.

  3. With operating the brake pedal, check voltage between BCM harness connector and ground.

    With ProPILOT assist 2.1
    + - Condition

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    E60 115 Ground Ignition switch ON Brake pedal is released 0V
    OFF
    ON Brake pedal is depressed Battery voltage
    OFF
    116 ON Brake pedal is released Battery voltage
    OFF 0 V
    ON Brake pedal is depressed 0 V
    OFF
    Without ProPILOT assist 2.1
    + - Condition

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    E29 110 Ground Ignition switch ON Brake pedal is released 0V
    OFF
    ON Brake pedal is depressed Battery voltage
    OFF
    111 ON Brake pedal is released Battery voltage
    OFF 0 V
    ON Brake pedal is depressed 0 V
    OFF

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

GO TO 6.

CHECK STOP LAMP SWITCH

Check stop lamp switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Replace stop lamp switch. Refer to Exploded View (with ProPILOT assist 2.1) or Exploded View (without ProPILOT assist 2.1).

CHECK STOP LAMP SWITCH CIRCUIT (OPEN)

  1. Disconnect following connectors:

    • BCM

    • Stop lamp switch

  2. Check continuity between BCM harness connector and stop lamp switch harness connector.

    With ProPILOT assist 2.1
    BCM Stop lamp switch Continuity
    Connector Terminal Connector Terminal
    E60 115 E38 2 Yes
    116 3
    Without ProPILOT assist 2.1
    BCM Stop lamp switch Continuity
    Connector Terminal Connector Terminal
    E29 110 E38 2 Yes
    111 3

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair or replace harness.

CHECK STOP LAMP / HIGH-MOUNTED STOP LAMP OUTPUT VOLTAGE

CONSULT

  1. Ignition switch ON.

  2. Select “Stop lamp 1” or “Stop lamp 2” in “Active test” mode of "BCM".

  3. With operating the test items, check voltage between BCM harness connector and ground.

    Stop lamp RH (with ProPILOT assist 2.1)
    + - Test item

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    B125 157 Ground Stop lamp 1 On Battery voltage
    Off 0V
    Stop lamp LH and high-mounted stop lamp (with ProPILOT assist 2.1)
    + - Test item

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    B125 160 Ground Stop lamp 2 On Battery voltage
    Off 0V
    Stop lamp RH (without ProPILOT assist 2.1)
    + - Test item

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    B27 157 Ground Stop lamp 1 On Battery voltage
    Off 0V
    Stop lamp LH and high-mounted stop lamp (without ProPILOT assist 2.1)
    + - Test item

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    B27 160 Ground Stop lamp 2 On Battery voltage
    Off 0V

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

GO TO 9.

CHECK STOP LAMP / HIGH-MOUNTED STOP LAMP POWER SUPPLY CIRCUIT (SHORT)

  1. Ignition switch OFF.

  2. Disconnect BCM connector.

  3. Check continuity between BCM harness connector and ground.

    Stop lamp RH (with ProPILOT assist 2.1)
    BCM — Continuity
    Connector Terminal
    B125 157 Ground No
    Stop lamp LH and high-mounted stop lamp (with ProPILOT assist 2.1)
    BCM — Continuity
    Connector Terminal
    B125 160 Ground No
    Stop lamp RH (without ProPILOT assist 2.1)
    BCM — Continuity
    Connector Terminal
    B27 157 Ground No
    Stop lamp LH and high-mounted stop lamp (without ProPILOT assist 2.1)
    BCM — Continuity
    Connector Terminal
    B27 160 Ground No

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK STOP LAMP / HIGH-MOUNTED STOP LAMP POWER SUPPLY CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect following connectors:

    • BCM

    • Rear combination lamp LH (body side)

    • Rear combination lamp RH (body side)

    • High-mounted stop lamp

  3. Check continuity between BCM harness connector and each stop lamp harness connector.

    Stop lamp (with ProPILOT assist 2.1)
    BCM Rear combination lamp (body side) Continuity
    Connector Terminal Connector Terminal
    RH B125 157 B102 3 Yes
    LH 160 B90
    High-mounted stop lamp (with ProPILOT assist 2.1)
    BCM High-mounted stop lamp Continuity
    Connector Terminal Connector Terminal
    B125 160 D503 2 Yes
    Stop lamp (without ProPILOT assist 2.1)
    BCM Rear combination lamp (body side) Continuity
    Connector Terminal Connector Terminal
    RH B27 157 B102 3 Yes
    LH 160 B90
    High-mounted stop lamp (without ProPILOT assist 2.1)
    BCM High-mounted stop lamp Continuity
    Connector Terminal Connector Terminal
    B27 160 D503 2 Yes

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair or replace harness.

CHECK STOP LAMP / HIGH-MOUNTED STOP LAMP GROUND CIRCUIT

Check continuity between each stop lamp harness connector and ground.

Stop lamp
Rear combination lamp (body side) — Continuity
Connector Terminal
RH B102 1 Ground Yes
LH B90
High-mounted stop lamp
High-mounted stop lamp — Continuity
Connector Terminal
D503 1 Ground Yes

Is the inspection result normal?

YES>>

Stop lamp: Check corresponding rear combination lamp (body side) sub harness, if there is a malfunction, repair or replace. If there is no malfunction, replace the corresponding rear combination lamp (body side). Refer to Removal and Installation.

YES>>

High-mounted stop lamp: Replace high-mounted stop lamp. Refer to Removal and Installation.

NO>>

Repair or replace harness.

Component Inspection

CHECK STOP LAMP SWITCH-1

  1. Ignition switch OFF.

  2. Disconnect stop lamp switch connector.

  3. Check continuity between stop lamp switch terminals.

    Stop lamp switch Condition Continuity
    Terminal
    + –
    1 2 Brake pedal Depressed Yes
    Fully released No
    3 4 Depressed No
    Fully released Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

GO TO 2.

CHECK STOP LAMP SWITCH-2

  1. Adjust stop lamp switch installation. Refer to Inspection and Adjustment.

  2. Check continuity of stop lamp switch terminals.

    Stop lamp switch Condition Continuity
    Terminal
    + –
    1 2 Brake pedal Depressed Yes
    Fully released No
    3 4 Depressed No
    Fully released Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace stop lamp switch. Refer to Exploded View (with ProPILOT assist 2.1) or Exploded View (without ProPILOT assist 2.1).

    License Plate Lamp Circuit
    Component Function Check CHECK TAIL LAMP OPERATION Check that tail lamp is turned ON when lighting switch is turned 1ST. Is the inspection result normal? YES>> GO TO 2. NO...
    Stop Lamp Relay Circuit
    Diagnosis Procedure CHECK STOP LAMP OPERATION Check that stop lamp is turned ON/OFF when the brake pedal is depressed/released. Is the inspection result normal? YES>> GO T...

    Other materials:

    U1caa-02 Mode Door Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U1CAA-02 Mode door motor (Mode door motor) Diagnosis condition Ignition switch ON Signal (Terminal) LIN (door motor) signal Threshold A/C amp. is no ...

    P064a Fuel Pump Control Module
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P064A 00 Fuel pump control module A (Fuel Pump Control Module "A") Diagnosis condition Engine running Signal (terminal) — Threshold Voltage s ...

    How to Use This Manual. How to Read Wiring Diagrams
    Connector Symbols Most of connector symbols in wiring diagrams are shown from the terminal side. Connector symbols shown from the terminal side are enclosed by a single line and followed by the direction mark. Connector symbols shown from the harness side are enclosed by a double line and ...