Nissan Rogue (T33) 2021-Present Service Manual: C1f00-44 Control Unit

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Adas Control Unit :: Dtc/circuit Diagnosis / C1f00-44 Control Unit

Without Propilot Assist 2.1

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
 
C1F00 44

CONTROL UNIT

(Control unit) 		Diagnosis condition When engine is running
Signal (terminal) —
Threshold ADAS control unit 2 internal malfunction
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

ADAS control unit 2

FAIL-SAFE

The following systems are canceled.

  • Vehicle-to-vehicle distance control mode

  • Conventional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • RAB

  • I-FCW

  • LDW

  • I-LI

  • BSW

  • I-BSI

  • RCTA

  • TSR

  • I-DA

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C1F00-44” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS 2”.

Is “C1F00-44” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK SELF-DIAGNOSIS RESULTS

Check if any DTC other than “C1F00-XX”, is detected in “Self Diagnostic Result” of “ICC/ADAS 2”.

Is any DTC detected?

YES>>

Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to DTC Index.

NO>>

Replace the ADAS control unit 2. Refer to Removal and Installation.

With Propilot Assist 2.1

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
 
C1F00 44

CONTROL UNIT

(Control unit) 		Diagnosis condition When engine is running
Signal (terminal) —
Threshold ADAS control unit 2 internal malfunction
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

ADAS control unit 2

FAIL-SAFE

The following systems are canceled.

  • Vehicle speed & vehicle-to-vehicle control function

  • Lane keep function*1

  • Lane keep function*2

  • Lane change support function

  • Overtaking support function

  • Route driving support function

  • FEB

  • RAB

  • PFCW

  • LDP

  • Blind Spot Intervention

  • TSR

  • DAA

*1: ProPILOT Assist 2.1 display is green

*2: ProPILOT Assist 2.1 display is blue

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C1F00-44” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS 2”.

Is “C1F00-44” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK SELF-DIAGNOSIS RESULTS

Check if any DTC other than “C1F00-44”, “C1F00-45”, “C1F00-46”, “C1F00-47”, “C1F00-49”, “C1F00-71”, “C1F00-87” and “C1F96-29” is detected in “Self Diagnostic Result” of “ICC/ADAS 2”.

Is any DTC detected?

YES>>

Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to DTC Index.

NO>>

Replace the ADAS control unit 2. Refer to Removal and Installation.

    C1f00-1c Control Unit
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1F00 1C CONTROL UNIT (Control unit) Diagnosis condition When en...
    C1f00-47 Control Unit
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F00 47 CONTROL UNIT (Control unit) Diagnosis condition ...

    Other materials:

    2wd. Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting
    Noise, Vibration and Harshness (nvh) Troubleshooting NVH Troubleshooting Chart Use chart below to find the cause of the symptom. If necessary, repair or replace these parts. Possible cause and SUSPECTED PARTS Symptom Reference DRIVE SHAFT FRONT AXLE Noise Shake Noise Shake Vibration ...

    A/f Sensor 1 Heater
    Component Inspection CHECK AIR FUEL RATIO (A/F) SENSOR 1 Turn ignition switch OFF. Disconnect A/F sensor 1 harness connector. Check resistance between A/F sensor 1 terminals as per the following. A/F sensor 1 Resistance + − Terminal 3 4 1.8 - 2.44 Ω [at 20°C ( ...

    Writing of Calibration Data
    Work Procedure DESCRIPTIONIf only the around view monitor control unit is replaced, the calibration data stored in the camera can be written to the around view monitor control unit by selecting "Camera Calibration" of "Work Support" mode in CONSULT.WORK PROCEDUREWRITE CALIBRATION DATA With C ...