Nissan Rogue (T33) 2021-Present Service Manual: Turn Signal Lamp Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Exterior Lighting System / Led Headlamp :: Dtc/circuit Diagnosis / Turn Signal Lamp Circuit

Component Function Check

CHECK TURN SIGNAL LAMP OPERATION

CONSULT

  1. Ignition switch ON.

  2. Select “Flasher” in “Active test” mode of “BCM”.

  3. With operating the test item, check that the turn signal lamp is blinks.

    RH : Turn signal lamps RH blink
    LH : Turn signal lamps LH blink
    LH/RH : Turn signal lamps RH and LH blinks

Is the inspection result normal?

YES>>

Turn signal lamp circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK SYMPTOM

Check symptom (A or B)

Symptom
A All of turn signal lamp are not blinks
B Applicable side performs high flasher activation

Which symptom is detected?

A>>

GO TO 2.

B>>

GO TO 4.

CHECK FUSE

  1. Ignition switch OFF.

  2. Check that the following fuse is not blown (open):

    Unit Location Fuse No. Capacity
    Battery power supply Fuse block (J/B) 58 15 A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 3.

CHECK BCM POWER SUPPLY (TURN SIGNAL LAMP)

  1. Disconnect BCM connector.

  2. Check voltage between BCM harness connector and ground.

    With type A meter
    + -

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    B124 137 Ground Battery voltage
    With type B meter
    + -

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    B23 136 Ground Battery voltage

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK TURN SIGNAL LAMP BULB

  1. Ignition switch OFF.

  2. Check each turn signal lamp bulb.

NOTE:

Except side turn signal lamp and front turn signal lamp (LED type).

Is the inspection result normal?

YES>>

GO TO 5.

NO-1>>

Front turn signal lamp (bulb type): Replace the corresponding front combination lamp bulb. Refer to Replacement.

NO-2>>

Rear turn signal lamp: Replace the corresponding rear combination lamp (body side) bulb. Refer to Replacement.

CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE

  1. Ignition switch ON.

  2. With operating the turn signal switch, check voltage between BCM harness connector and ground.

    Front turn signal lamp (with type A meter)
    + - Condition

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    RH E60 127 Ground Turn signal switch Right Blinking : 0 V <–> Battery voltage
    Center 0 V
    LH 128 Left Blinking : 0 V <–> Battery voltage
    Center 0 V
    Front turn signal lamp (with type B meter)
    + - Condition

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    RH E29 116 Ground Turn signal switch Right Blinking : 0 V <–> Battery voltage
    Center 0 V
    LH 128 Left Blinking : 0 V <–> Battery voltage
    Center 0 V
    Side turn signal lamp (with type A meter)
    + - Condition

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    RH M62 178 Ground Turn signal switch Right Blinking : 0 V <–> Battery voltage
    Center 0 V
    LH 179 Left Blinking : 0 V <–> Battery voltage
    Center 0 V
    Side turn signal lamp (with type B meter)
    + - Condition

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    RH M18 1 Ground Turn signal switch Right Blinking : 0 V <–> Battery voltage
    Center 0 V
    LH 21 Left Blinking : 0 V <–> Battery voltage
    Center 0 V
    Rear turn signal lamp (with type A meter)
    + - Condition

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    RH B125 159 Ground Turn signal switch Right Blinking : 0 V <–> Battery voltage
    Center 0 V
    LH 150 Left Blinking : 0 V <–> Battery voltage
    Center 0 V
    Rear turn signal lamp (with type B meter)
    + - Condition

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    RH B27 159 Ground Turn signal switch Right Blinking : 0 V <–> Battery voltage
    Center 0 V
    LH 151 Left Blinking : 0 V <–> Battery voltage
    Center 0 V

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 6.

CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (SHORT)

  1. Ignition switch OFF.

  2. Disconnect BCM connector.

  3. Check continuity between BCM harness connector and ground.

    Front turn signal lamp (with type A meter)
    BCM — Continuity
    Connector Terminal
    RH E60 127 Ground No
    LH 128
    Front turn signal lamp (with type B meter)
    BCM — Continuity
    Connector Terminal
    RH E29 116 Ground No
    LH 128
    Side turn signal lamp (with type A meter)
    BCM — Continuity
    Connector Terminal
    RH M62 178 Ground No
    LH 179
    Side turn signal lamp (with type B meter)
    BCM — Continuity
    Connector Terminal
    RH M18 1 Ground No
    LH 21
    Rear turn signal lamp (with type A meter)
    BCM — Continuity
    Connector Terminal
    RH B125 159 Ground No
    LH 150
    Rear turn signal lamp (with type B meter)
    BCM — Continuity
    Connector Terminal
    RH B27 159 Ground No
    LH 151

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect BCM connector and each turn signal lamp connector.

  3. Check continuity between BCM harness connector and each turn signal lamp harness connector.

    Front turn signal lamp (with type A meter)
    BCM Front combination lamp Continuity
    Connector Terminal Connector Terminal
    RH E60 127 E105 11 Yes
    LH 128 E103
    Front turn signal lamp (with type B meter)
    BCM Front combination lamp Continuity
    Connector Terminal Connector Terminal
    RH E29 116 E105 11 Yes
    LH 128 E103
    Side turn signal lamp (with type A meter and automatic drive positioner)
    BCM Door mirror Continuity
    Connector Terminal Connector Terminal
    RH M62 178 D106 11 Yes
    LH 179 D16
    Side turn signal lamp (with type B meter and automatic drive positioner)
    BCM Door mirror Continuity
    Connector Terminal Connector Terminal
    RH M18 1 D106 11 Yes
    LH 21 D16
    Side turn signal lamp (with type A meter, without automatic drive positioner)
    BCM Door mirror Continuity
    Connector Terminal Connector Terminal
    RH M62 178 D107 10 Yes
    LH 179 D14
    Side turn signal lamp (with type B meter, without automatic drive positioner)
    BCM Door mirror Continuity
    Connector Terminal Connector Terminal
    RH M18 1 D107 10 Yes
    LH 21 D14
    Rear turn signal lamp (with type A meter)
    BCM Rear combination lamp (body side) Continuity
    Connector Terminal Connector Terminal
    RH B125 159 B102 4 Yes
    LH 150 B90
    Rear turn signal lamp (with type B meter)
    BCM Rear combination lamp (body side) Continuity
    Connector Terminal Connector Terminal
    RH B27 159 B102 4 Yes
    LH 151 B90

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair or replace harness.

CHECK TURN SIGNAL LAMP GROUND CIRCUIT

Check continuity between each turn signal lamp harness connector and ground.

Front turn signal lamp
Front combination lamp — Continuity
Connector Terminal
RH E105 12 Ground Yes
LH E103
Side turn signal lamp (with automatic drive positioner)
Door mirror — Continuity
Connector Terminal
RH D106 9 Ground Yes
LH D16
Side turn signal lamp (without automatic drive positioner)
Door mirror — Continuity
Connector Terminal
RH D107 12 Ground Yes
LH D14
Rear turn signal lamp
Rear combination lamp (body side) — Continuity
Connector Terminal
RH B102 1 Ground Yes
LH B90

Is the inspection result normal?

YES-1>>

Front turn signal lamp (LED type): Replace the corresponding front combination lamp. Refer to Removal and Installation.

YES-2>>

Front turn signal lamp (bulb type): Replace corresponding front combination lamp bulb. Refer to Replacement.

YES-3>>

Side turn signal lamp: Replace corresponding side turn signal lamp. Refer to Removal and Installation.

YES-4>>

Rear turn signal lamp: Check corresponding rear combination lamp (body side) sub harness, if there is a malfunction, repair or replace. If there is no malfunction, replace the corresponding rear combination lamp (body side) bulb. Refer to Replacement.

NO>>

Repair or replace harness.

    Back-Up Lamp Circuit
    Component Function Check CHECK BACK-UP LAMP OPERATION Start the engine. With operating the shift selector, check that the back-up lamp is turned ON. Shift selector position: R r...
    Hazard Switch Circuit
    Component Function Check CHECK HAZARD SWITCH SIGNAL CONSULT Ignition switch ON. Select “Hazard switch” in “Data monitor” mode “BCM [FLASHER]”. With operating the haz...

    Other materials:

    Informations de base
    AVERTISSEMENT Le non-respect des instructions et avertissements relatifs à l’utilisation correcte du détecteur de collision frontale intelligent du Nissan Rogue peut entraîner des blessures graves, voire mortelles. Le détecteur de collision frontale intelligent sert uniquement à averti ...

    U00ac Lin Communication
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U00AC 00 USM-IBS LIN Communication Failure (USM-IBS LIN Communication Failure ) Diagnosis condition Ignition switch ON Signal LIN communication Th ...

    Informations de base
    Spot de lecture avant Éclairage de miroir de courtoisie (si équipé) Plafonnier (si équipé) Clignotant latéral (si équipé) Éclairage individuel arrière (si équipé) Phare – feu de route Phare – feu de croisement Feu de stationnement avant / éclairage de jour / c ...