Nissan Rogue (T33) 2021-Present Service Manual: Hazard Switch Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Exterior Lighting System / Led Headlamp :: Dtc/circuit Diagnosis / Hazard Switch Circuit

Component Function Check

CHECK HAZARD SWITCH SIGNAL

CONSULT

  1. Ignition switch ON.

  2. Select “Hazard switch” in “Data monitor” mode “BCM [FLASHER]”.

  3. With operating the hazard switch, check the monitor status.

    Monitor item Condition Monitor status
    Hazard switch Hazard switch ON On
    OFF Off

Is the inspection result normal?

YES>>

Hazard switch circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK HAZARD SWITCH SIGNAL

  1. Ignition switch OFF.

  2. Disconnect hazard switch connector.

  3. Check voltage between hazard switch harness connector and ground.

    + -

    Voltage

    (Approx.)
    Hazard switch
    Connector Terminal
    M26 2 Ground Battery votlage

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 2.

CHECK HAZARD SWITCH SIGNAL CIRCUIT (OPEN)

  1. Disconnect BCM connector.

  2. Check continuity between hazard switch harness connector and BCM harness connector.

    With type A meter
    Hazard switch BCM Continuity
    Connector Terminal Connector Terminal
    M26 2 M62 161 Yes
    With type B meter
    Hazard switch BCM Continuity
    Connector Terminal Connector Terminal
    M26 2 M18 13 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness.

CHECK HAZARD SWITCH SIGNAL CIRCUIT (SHORT)

Check continuity between hazard switch harness connector and ground.

Hazard switch — Continuity
Connector Terminal
M26 2 Ground No

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK HAZARD SWITCH GROUND CIRCUIT

Check continuity between hazard switch harness connector and ground.

Hazard switch — Continuity
Connector Terminal
M26 3 Ground Yes

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness.

CHECK HAZARD SWITCH

Check hazard switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace hazard switch. Refer to Removal and Installation.

Component Inspection

CHECK HAZARD SWITCH

  1. Ignition switch OFF.

  2. Disconnect hazard switch connector.

  3. Check continuity between hazard switch terminals.

    Hazard switch Condition Continuity
    Terminal
    + –
    2 3 Hazard switch ON Yes
    OFF No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace hazard switch. Refer to Removal and Installation.

    Turn Signal Lamp Circuit
    Component Function Check CHECK TURN SIGNAL LAMP OPERATION CONSULT Ignition switch ON. Select “Flasher” in “Active test” mode of “BCM”. With operating the test item, ...
    Led Headlamp. Symptom Diagnosis
    Exterior Lighting System Symptoms Symptom Table NOTE: Perform self diagnosis result with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any DTC is detect...

    Other materials:

    P0531 A/c Refrigerant Pressure Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0531 00 REFRIGERANT PRESS SENSOR A (A/C refrigerant pressure sensor A circuit range/performance Diagnosis condition Engine running at idle Signal (termin ...

    Back-Up Lamp Circuit
    Component Function Check CHECK BACK-UP LAMP OPERATION Start the engine. With operating the shift selector, check that the back-up lamp is turned ON. Shift selector position: R range : Back-up lamp ON Shift selector position: Other than above : Back-up lamp OFF Is th ...

    Removal and Installation. Steering Member Assembly
    Exploded View Steering member brace Steering member assembly     Removal and Installation Remove instrument panel assembly. Refer to Removal and Installation. Remove driver knee air bag. Refer to Removal and Installation. Remove passenger knee air bag. Refer to Remova ...