Nissan Rogue (T33) 2021-Present Service Manual: Led Headlamp :: Symptom Diagnosis

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Exterior Lighting System / Led Headlamp :: Symptom Diagnosis

Exterior Lighting System Symptoms

Symptom Table

NOTE:

Perform self diagnosis result with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any DTC is detected.

Symptom		Possible cause	Inspection item
Headlamp (HI) is not turned ON	One side	Headlamp LED [headlamp (HI)] LED headlamp control module Harness	Replace corresponding front combination lamp Refer to Removal and Installation.
Headlamp (HI) is not turned ON	Both sides	Symptom diagnosis “BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON” Refer to Diagnosis Procedure.
High beam indicator is not turned ON [headlamp (HI) is turned ON]		Combination meter	"M&A" "Data monitor" “HI-BEAM IND”
Headlamp (LO) is not turned ON	One side	Headlamp LED [headlamp (LO)] LED headlamp control module Harness	Replace corresponding front combination lamp Refer to Removal and Installation.
Headlamp (LO) is not turned ON	Both sides	Symptom diagnosis “BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON” Refer to Diagnosis Procedure.
Each lamp is not turned ON/OFF with lighting switch AUTO (with ProPILOT assist 2.1)		Combination switch input/output signal circuit Combination switch BCM	Combination switch Refer to Symptom Table.
		Rain and light sensor power/ground/LIN circuit Rain and light sensor BCM	Rain and light sensor circuit Refer to Component Function Check.
Each lamp is not turned ON/OFF with lighting switch AUTO (without ProPILOT assist 2.1)		Combination switch input/output signal circuit Combination switch BCM	Combination switch Refer to Symptom Table.
		Optical sensor power/ground/signal circuit Optical sensor BCM	Optical sensor circuit Refer to Component Function Check.
Parking lamp is not turned ON		Front combination lamp LED (parking lamp) LED headlamp control module Harness	Replace corresponding front combination lamp Refer to Removal and Installation.
Front side marker lamp is not turned ON		Front side marker lamp power supply/ground circuit Front side marker lamp bulb Front side marker lamp bulb socket	Front side marker lamp circuit Refer to Component Function Check.
Tail lamp and rear side marker lamp is not turned ON		Tail lamp power supply/ground circuit Rear combination lamp (body side) LED (tail lamp) Rear side marker lamp bulb Rear side marker lamp bulb socket Sub harness Rear combination lamp (back door side) LED (tail lamp) Sub harness IPDM E/R	Tail lamp circuit Refer to Component Function Check.
Back-up lamp is not turned on with shift selector in R position		Back-up lamp relay power supply/control circuit Back-up lamp relay Back-up lamp power supply/ground circuit Rear combination lamp (back door side) LED (back-up lamp) Sub harness	Back-up lamp circuit Refer to . Component Function Check.
		TCM	"TRANSMISSION" "Data monitor" "Range"
License plate lamp is not turned ON		License plate lamp power supply/ground circuit License plate lamp bulb License plate lamp bulb socket	License plate lamp circuit Refer to Component Function Check.
Parking lamp, license plate lamp, side marker lamp and tail lamp are not turned ON		Symptom diagnosis “PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT TURNED ON” Refer to Diagnosis Procedure.
Position light indicator is not turned ON (parking lamp, license plate lamp, side marker lamp and tail lamp are turned ON)		Combination meter	"M&A" "Data monitor" “LIGHT IND”
Daytime running light is not turned ON		Front combination lamp LED (daytime running light) LED headlamp control module Harness	Replace corresponding front combination lamp Refer to Removal and Installation.
Turn signal lamp does not blink	Indicator is normal (all of turn signal lamp is not blinks)	Fuse Battery power supply (turn signal lamp) circuit BCM	Turn signal lamp circuit Refer to Component Function Check.
	Indicator is normal (applicable side performs high flasher activation)	Front turn signal lamp Front turn signal lamp power supply/ground circuit Front combination lamp LED (front turn signal lamp) Front turn signal lamp bulb Front turn signal lamp bulb socket Side turn signal lamp Side turn signal lamp power supply/ground circuit Side turn signal lamp LED (side turn signal lamp) Rear turn signal lamp Rear turn signal lamp power supply/ground circuit Rear turn signal lamp bulb Rear turn signal lamp bulb socket Sub harness BCM	Turn signal lamp circuit Refer to Component Function Check.
	Indicator is included	Combination switch input/output signal circuit Combination switch BCM	Combination switch Refer to Symptom Table.
Turn signal indicator does not blink (turn signal lamp is normal)	One side	Combination meter	—
	Both sides (always)	Turn indicator signal BCM Combination meter	"M&A" "Data monitor" “TURN IND”
	Both sides (only when activating hazard warning lamp with ignition switch OFF)	Combination meter power supply/ground circuit Combination meter	Combination meter Power supply and ground circuit Refer toDiagnosis Procedure (with type A meter) or Diagnosis Procedure (with type B meter).
Hazard warning lamp does not activate (turn signal lamp is normal) Hazard warning lamp continues activating		Hazard switch signal/ground circuit Hazard switch BCM	Hazard switch circuit Refer to Component Function Check.
Stop lamp and high-mounted stop lamp are not turned ON	All of stop lamp and high-mounted stop lamp are not turned ON	Fuse Battery power supply (stop lamp) circuit Stop lamp switch power supply/signal circuit Stop lamp switch BCM	Stop lamp circuit Refer to Component Function Check.
Stop lamp and high-mounted stop lamp are not turned ON	Any of stop lamp and high-mounted stop lamp are not turned ON	Fuse Stop lamp Stop lamp power supply/ground circuit Rear combination lamp (body side) LED (stop lamp) Sub harness High-mounted stop lamp High-mounted stop lamp power supply/ground circuit High-mounted stop lamp LED (high-mounted stop lamp) BCM	Stop lamp circuit Refer to Component Function Check.
Stop lamp is not turned ON during AEB activation [AEB operates normally (with ProPILOT assist 2.1)]		Stop lamp relay power supply/control circuit Stop lamp power supply circuit Chassis control module	Stop lamp relay circuit Refer to Diagnosis Procedure.
HBA is not turned ON/OFF (without ProPILOT Assist 2.1)		Combination switch input/output signal circuit Combination switch BCM	Combination switch Refer to Symptom Table.
HBA is not turned ON/OFF (without ProPILOT Assist 2.1)		Optical sensor power/ground/signal circuit Optical sensor BCM	Optical sensor circuit Refer to Component Function Check.
HBA is not turned ON/OFF (with ProPILOT Assist 2.1)		Combination switch input/output signal circuit Combination switch BCM	Combination switch Refer to Symptom Table.
HBA is not turned ON/OFF (with ProPILOT Assist 2.1)		Rain and light sensor power/ground/LIN circuit Rain and light sensor BCM	Rain and light sensor circuit Refer to Component Function Check.

Normal Operating Condition

Description

LED HEADLAMP

LED brightness and color may slightly change until the temperature becomes stable. This is not malfunction.
Illumination time lag may occur between right and left. This is not malfunction.
Brightness may be reduced due to aged deterioration of LED.

INTELLIGENT AUTO LIGHT SYSTEM

The headlamp may not be turned ON/OFF immediately after passing dark area or bright area (short tunnel, sky bridge, shadowed area etc.) while using the intelligent auto light system. This causes for the control difference. This is normal.

HIGH BEAM ASSIST SYSTEM

When driving while using the high beam assist system, the headlamp beam may not switch or the beam switching timing may vary according to the ambient environment (the condition of the Nissan Ariya vehicle ahead, the condition of the road, the position of the vehicle, etc.).This is due to control differences and is not a malfunction.

Both Side Headlamps (hi) Are Not Turned on

Description

Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.

Diagnosis Procedure

COMBINATION SWITCH INSPECTION

Check combination switch. Refer to Symptom Table.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace the malfunctioning part.

CHECK HIGH BEAM REQUEST SIGNAL

CONSULT

Select “High beam request” in “Data monitor” mode of “IPDM E/R”.
With operating the lighting switch, check the monitor status.

Monitor item Condition Monitor status

High beam request Lighting switch (2ND) HI On

LO Off

Monitor item	Condition	Monitor status
High beam request	Lighting switch (2ND)	HI	On
LO	Off

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Replace BCM. Refer to Removal and Installation.

Both Side Headlamps (lo) Are Not Turned on

Description

Both side headlamps (LO) are not turned ON in any condition.

Diagnosis Procedure

CHECK COMBINATION SWITCH

Check combination switch. Refer to Symptom Table.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace the malfunctioning part.

CHECK LOW BEAM REQUEST SIGNAL

CONSULT

Select “Low beam request” in “Data monitor” mode of “IPDM E/R”.
With operating the lighting switch, check the monitor status.

Monitor item Condition Monitor status

Low beam request Lighting switch 2ND On

OFF or AUTO* Off

*: Only when the illumination judgement by intelligent auto light system is OFF.

Monitor item	Condition	Monitor status
Low beam request	Lighting switch	2ND	On
OFF or AUTO*	Off

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Replace BCM. Refer to Removal and Installation.

Parking, License Plate, Side Marker and Tail Lamps Are Not Turned on

Description

The parking, license plate, side marker and tail lamps are not turned ON in any condition.

Diagnosis Procedure

COMBINATION SWITCH INSPECTION

Check combination switch. Refer to Symptom Table.

Is the combination switch normal?

YES>>

GO TO 2.

NO>>

Repair or replace the malfunctioning part.

CHECK POSITION LIGHT REQUEST SIGNAL

CONSULT

Select “Position light request” in “Data monitor” mode of “IPDM E/R”.
With operating the lighting switch, check the monitor status.

Monitor item Condition Monitor status

Position light request Lighting switch 1ST On

OFF or AUTO* Off

*: Only when the illumination judgement by intelligent auto light system is OFF.

Monitor item	Condition	Monitor status
Position light request	Lighting switch	1ST	On
OFF or AUTO*	Off

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Replace BCM. Refer to Removal and Installation.

 Hazard Switch Circuit

Component Function Check CHECK HAZARD SWITCH SIGNAL CONSULT Ignition switch ON. Select “Hazard switch” in “Data monitor” mode “BCM [FLASHER]”. With operating the haz...

 Led Headlamp. Periodic Maintenance. Headlamp Aiming Adjustment

Headlamp Aiming Adjustment Adjustment DESCRIPTIONPREPARATION BEFORE ADJUSTINGNOTE: For details, refer to the regulations in your own country. Perform aiming if the Nissan Ariya ...

Other materials:

Crevaison
Système de contrôle de la pression des pneus (TPMS) Ce véhicule Nissan Rogue est équipé du système de contrôle de la pression des pneus (TPMS), conçu pour assister le conducteur dans la surveillance permanente de la pression des pneumatiques afin d’améliorer la sécurité, la stabilité ...

Fusibles
Compartiment moteur Informations de base AVERTISSEMENT N’utilisez jamais un fusible dont l’ampérage est supérieur ou inférieur à la valeur indiquée sur le couvercle de la boîte à fusibles. L’utilisation d’un fusible inadapté peut endommager le circuit électrique, les unit ...

Comment utiliser la fonction de verrouillage à télécommande sans clé du Nissan Rogue
AVERTISSEMENTS DE SÉCURITÉ IMPORTANTS Équipements médicaux : Les ondes radio émises par la clé intelligente de votre Nissan Rogue peuvent potentiellement interférer avec le fonctionnement des équipements médicaux électriques. Avant toute utilisation du système, toute personne porte ...