Nissan Rogue (T33) 2021-Present Service Manual: P11b1 Vcr Target Angle (cold Start)

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P11b1 Vcr Target Angle (cold Start)

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P11B1 00

VCR target angle (cold start)

[Variable compression ratio target angle (cold start)] 		Diagnosis condition Engine running at idle
Signal (terminal) —
Threshold There is a gap between angle of target and phase-control angle degree (Low compression ratio)
Diagnosis delay time 110 seconds or more

POSSIBLE CAUSE

  • VCR actuator

  • VCR control module connector

  • Foreign objects interferes with VCR actuator

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

CHECK OTHER DTC

When this DTC is detected, perform trouble diagnosis for other DTC.

>>

DTC Diagnosis Procedure

DTC Diagnosis Procedure

CHECK OTHER DTC

If DTC P11B1 is displayed with the following DTC, perform the confirmation procedure (trouble diagnosis) for the applicable DTC.

Is DTC P11A0, P11A1, P11A2, P11A3 P11A4, P11A6, P11A7, P11AB, P11AC, P11AD, P11AE or P11AF detected?

YES>>

Perform diagnosis of applicable.

  • DTC P11A0: DTC Description.

  • DTC P11A1: DTC Description.

  • DTC P11A2: DTC Description.

  • DTC P11A3: DTC Description.

  • DTC P11A4: DTC Description.

  • DTC P11A6: DTC Description.

  • DTC P11A7: DTC Description.

  • DTC P11AB: DTC Description.

  • DTC P11AC: DTC Description.

  • DTC P11AD: DTC Description.

  • DTC P11AE: DTC Description.

  • DTC P11AF: DTC Description.

NO>>

GO TO 2.

CHECK VCR CONTROL MODULE CONNECTOR

  1. Disconnect VCR control module connector.

  2. Connect VCR control module connector.

  3. Perform DTC Confirmation Procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK VCR MOTOR

Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace VCR actuator. Refer to Removal and Installation.

    P11b0 Vcr Target Angle (cold Start)
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11B0 00 VCR target angle (cold start) [Variable compression rat...
    P1217 Engine Over Temperature
    DTC Description DTC DETECTION LOGICIf the cooling fan or another component in the cooling system malfunctions, engine coolant temperature will rise.When the engine coolant tempe...

    Other materials:

    Meter Speaker Signal Circuit
    Diagnosis Procedure CHECK METER SPEAKER CIRCUIT FOR OPEN Ignition switch OFF. Disconnect combination meter harness connector and meter speaker harness connector. Check the continuity between combination meter harness connector and meter speaker harness connector. Combination meter ...

    B2223-1c Combination Meter
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detected condition B2223-1C Combination meter (Combination meter) Diagnosis condition When ignition switch is ON. Signal (terminal) — Threshold TFT error is detected ...

    P050a Cold Start Control
    DTC Description DESCRIPTIONECM controls ignition timing and engine idle speed when engine is started with pre-warming up condition.This control promotes the activation of three way catalyst by heating the catalyst and reduces emissions.DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diag ...