Nissan Rogue (T33) 2021-Present Service Manual: P1217 Engine Over Temperature

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P1217 Engine Over Temperature

DTC Description

DTC DETECTION LOGIC

If the cooling fan or another component in the cooling system malfunctions, engine coolant temperature will rise.

When the engine coolant temperature reaches an abnormally high temperature condition, a malfunction is indicated.

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P1217 00

OVER TEMP

[OVER HEAT] 		Diagnosis condition —
Signal (terminal) —
Threshold Engine coolant temperature reaches an abnormally high temperature
Diagnosis delay time —

CAUTION:

When a malfunction is indicated, be sure to replace the coolant. Also, replace the engine oil.

  1. Fill radiator with coolant up to specified level with a filling speed of 2 liters per minute. Be sure to use coolant with the proper mixture ratio.

  2. After refilling coolant, run engine to ensure that no water-flow noise is emitted.

POSSIBLE CAUSE

  • Harness or connectors (Cooling fan circuit is open or shorted.)

  • IPDM E/R

  • Cooling fan control module

  • Cooling fan motor

  • Cooling fan

  • Radiator hose

  • Radiator

  • Radiator cap

  • Water pump

  • Multi-way control valve

  • Amount of engine coolant

FAIL-SAFE

Engine Control System

Not applicable

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited.

When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P1217 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or P0607.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM COMPONENT FUNCTION CHECK

Perform component function check. Refer to Component Inspection.

NOTE:

Use component function check to check the overall function of the cooling fan. During this check, a DTC might not be confirmed.

Is the inspection result normal?

YES-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

YES-2>>

Confirmation after repair: INSPECTION END

NO>>

Proceed to DTC Diagnosis Procedure.

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P1217 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or P0607.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK COOLING FAN OPERATION

With CONSULT

  1. Turn ignition switch ON.

  2. Perform “FAN DUTY CONTROL” in “ACTIVE TEST” mode of “ENGINE” using CONSULT.

  3. Check that cooling fan speed varies according to the percentage.

Without CONSULT

  1. Activate IPDM E/R auto active test and check cooling fan motors operation. Refer to CONSULT Function (IPDM E/R).

  2. Check that cooling fan operates.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Refer to Diagnosis Procedure.

CHECK COOLING SYSTEM FOR LEAK-1

Check cooling system for leak. Refer to Inspection.

Is leakage detected?

YES>>

GO TO 4.

NO>>

GO TO 5.

CHECK COOLING SYSTEM FOR LEAK-2

Check the following for leak.

  • Hose (Refer to Inspection.)

  • Radiator (Refer to Inspection.)

  • Water pump (Refer to Removal and Installation.)

>>

Repair or replace malfunctioning part.

CHECK RADIATOR CAP

Check radiator cap. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Replace radiator cap. Refer to Inspection.

CHECK THERMOSTAT

Check thermostat. Refer to Exploded View.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Replace thermostat. Refer to Exploded View.

CHECK ENGINE COOLANT TEMPERATURE SENSOR

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Replace engine coolant temperature sensor. Refer to Removal and Installation.

OVERHEATING CAUSE ANALYSIS

If the cause cannot be isolated, Refer to Troubleshooting Chart.

>>

INSPECTION END

    P11b1 Vcr Target Angle (cold Start)
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11B1 00 VCR target angle (cold start) [Variable compression rat...
    P1225 Tp Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1225 00 CTP LEARNING-B1 (CTP LEARNING-B1) Diagnosis condition I...

    Other materials:

    Removal and Installation. Front and Rear Washer Pump
    Exploded View Washer tank Packing Front and rear washer pump : Nissan Ariya Vehicle front Removal and Installation CAUTION: When front and rear washer pump is removed, washer fluid may come out so prepare a container to receive the fluid and never allow fluid to be s ...

    Can Fundamental. Description
    Outline How to Use This Section “CAN FUNDAMENTAL” of LAN Section describes the basic knowledge of the CAN communication system and the method of trouble diagnosis. For information peculiar to a Nissan Ariya vehicle and inspection procedure, refer to “CAN”. System (can Commun ...

    Fuel Tank Temperature Sensor
    Component Inspection CHECK FUEL TANK TEMPERATURE (FTT) SENSOR Turn ignition switch OFF. Disconnect fuel level sensor unit and fuel pump harness connector. Check the resistance between fuel level sensor unit and fuel pump terminals. Fuel level sensor unit and fuel pump Condition R ...