Nissan Rogue (T33) 2021-Present Service Manual: P11a1 Vcr Motor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P11a1 Vcr Motor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P11A1 00

VCR motor

(Variable compression ratio motor) 		Diagnosis condition

  • Engine running at idle

  • Engine speed : 4,500 rpm or more
Signal (terminal) —
Threshold When VCR control module judges bad motor rotation, even though VCR control module commands the motor to rotate.
Diagnosis delay time 1 second

POSSIBLE CAUSE

  • VCR actuator (built-in VCR motor)

  • Foreign objects interferes with VCR actuator

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC P11A1 is displayed with the following DTC, perform the confirmation procedure (trouble diagnosis) for the applicable DTC.

Is DTC P11A0, P11A2, P11A3, P11A4 or P11AB detected?

YES>>

Perform diagnosis of applicable.

  • DTC P11A0: DTC Description

  • DTC P11A2: DTC Description

  • DTC P11A3: DTC Description

  • DTC P11A4: DTC Description

  • DTC P11AB: DTC Description

NO>>

GO TO 2.

PRECONDITIONING

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 12 V or more with ignition switch ON.

YES>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and warm it up to the normal operating temperature.

  2. Keep the engine speed between 4,500 rpm for at least 2 seconds under no load.

  3. Check 1st trip DTC.

Is DTC P11A1 detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P11A1 is displayed with the following DTC, perform the confirmation procedure (trouble diagnosis) for the applicable DTC.

Is DTC P11A0, P11A2, P11A3, P11A4 or P11AB detected?

YES>>

Perform diagnosis of applicable.

  • DTC P11A0: DTC Description

  • DTC P11A2: DTC Description

  • DTC P11A3: DTC Description

  • DTC P11A4: DTC Description

  • DTC P11AB: DTC Description

NO>>

GO TO 2.

CHECK VCR SYSTEM

With CONSULT

  1. Reconnect VCR control module and VCR actuator harness connector.

  2. Turn ignition switch ON.

  3. On CONSULT screen, select “ENGINE”>>“Active Test”>>“VCR system”.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace VCR actuator. Refer to Removal and Installation.

CHECK VCR MOTOR

Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair or replace malfunctioning parts.

    P11a0 Vcr Control Module
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11A0 00 VCR control module (Variable compression ratio control ...
    P11a2 Vcr Motor Rotation Angle Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11A2 00 VCR motor rotation angle sensor (Variable compression r...

    Other materials:

    Étiquette des pneus
    Exemple Informations de base La législation fédérale impose aux fabricants de pneus d’apposer sur le flanc de chaque pneu des informations normalisées et clairement lisibles. Ces marquages, présents sur les pneus du Nissan Rogue, permettent d’identifier les caractéristiques essenti ...

    Mac Key Writing
    Description When replacing around view monitor control unit, it is necessary to write MAC key to around view monitor control unit. Write MAC key to around view monitor control unit according to "MAC Key writing" procedure of "CONSULT Operation Manual". Refer to Work Procedure.CAUTION: During ...

    Preparation
    Special Service Tool The actual shapes of TechMate tools may differ from those of special service tools illustrated here. Tool number (TechMate No.) Tool name   Description (NI-39570) Chassis ear Locates the noise (NI-50397) Squeak and Rattle Kit Repairs the ca ...