Nissan Rogue (T33) 2021-Present Service Manual: P060c Ecm

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P060c Ecm

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P060C 00

Control module

(Internal Control Module Main Processor Performance) 		Diagnosis condition —
Signal (terminal) —
Threshold Built-in microcomputer system internal ECM does not function properly
Diagnosis delay time —

POSSIBLE CAUSE

ECM

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited. When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and keep the engine speed at 3,000 rpm for 5 seconds.

  2. Let it idle for at least 10 seconds.

  3. Turn ignition switch OFF and wait at least 10 seconds.

  4. Turn ignition switch ON.

  5. Check 1st trip DTC.

Is the DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure for 3 times. Refer to DTC Description.

Is the 1st trip DTC P060C displayed again?

YES>>

Replace ECM. Refer to ECM : Removal & Installation.

NO>>

INSPECTION END

    P060a Ecm
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P060A 00 CONTROL MODULE (Internal control module monitoring proc...
    P061b Ecm
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P061B 00 Internal control module (Internal Control Module Torque...

    Other materials:

    Symptom Diagnosis. Door Mirror Does Not Operate
    Diagnosis Procedure (Without automatic drive positioner system) CHECK DOOR MIRROR CIRCUIT Check door mirror. Refer to Diagnosis Procedure. Is the inspection result normal? YES>> GO TO 2. NO>> Repair or replace the malfunctioning parts. REPLACE DOOR MIRROR MOTOR Replace door mi ...

    P00fe Evap Control System
    DTC Description This diagnosis detects clogs in the EVAP line between fuel tank and EVAP canister purge volume control solenoid valve.ECM controls EVAP control system as below. ECM monitors EVAP line pressure change to diagnose if there is no clogging between EVAP canister and fuel tank. E ...

    C1f89-97 Side Radar Rear Lh
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1F89 97 Side radar rear LH (Side radar rear left hand) Diagnosis condition When engine is running Signal (terminal) CAN communication signal Threshold ...