Nissan Rogue (T33) 2021-Present Service Manual: P061b Ecm

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P061B 00

Internal control module

(Internal Control Module Torque Calculation Performance)
Diagnosis condition Engine running
Signal (terminal) —
Threshold Malfunction of ECM processor
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    (Circuit is open or shorted.)

  • ECM

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode
  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.

Electric throttle control cancel mode ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited. When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and let it idle for 30 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK FUEL INJECTOR

Check fuel injector. Refer to Component Function Check.

Is inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. DTC Description

  4. Check 1st trip DTC.

Is the DTC P062B displayed again?

YES>>

Replace ECM. Refer to ECM : Removal & Installation.

NO>>

INSPECTION END

    P060c Ecm
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P060C 00 Control module (Internal Control Module Main Processor ...
    P062b Ecm
    DTC Description This DTC is detected when the ECM-integrated injector driver unit has a malfunction.DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC ...

    Other materials:

    Removal and Installation. Filament
    Inspection and Repair INSPECTIONWhen measuring voltage, wrap tin foil around the top of the negative probe. Then press the foil against the wire with your finger. Attach probe circuit tester (in Volt range) to middle portion of each filament. If a filament is burned out, circuit teste ...

    Fondamentaux technologiques pour le Nissan Rogue
    Bouton d'accès rapide CAMÉRA AVERTISSEMENT SUR L'USAGE DU SYSTÈME Le non-respect des consignes d'utilisation de cet écran sur votre Nissan Rogue peut mener à des accidents graves. Ce système est une aide au confort et non un pilote automatique de stationnement. Des z ...

    Driver Monitor Camera (driver Monitor Camera Control Unit)
    B2a50-49 Driver Monitor Camera DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2A50 49 DRIVER MONITOR CAMERA Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Driver mo ...