Nissan Rogue (T33) 2021-Present Service Manual: P062b Ecm

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P062b Ecm

DTC Description

This DTC is detected when the ECM-integrated injector driver unit has a malfunction.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P062B 00

ECM

(Internal control module fuel injector control performance) 		Diagnosis condition Engine running at idle
Signal (terminal) —
Threshold Injector driver unit is malfunctioning
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (Fuel injector circuit is open or shorted.)

  • Battery power supply

  • ECM (Injector driver unit)

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

NOTE:

ECM does not control the accelerator pedal releasing speed.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited. When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

PRECONDITIONING

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and keep the engine speed at idle for 30 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK FUEL INJECTOR

Check fuel injector. Refer to Component Function Check.

Is inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. DTC Description

  4. Check 1st trip DTC.

Is the DTC P062B displayed again?

YES>>

Replace ECM. Refer to ECM : Removal & Installation.

NO>>

INSPECTION END

    P061b Ecm
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P061B 00 Internal control module (Internal Control Module Torque...
    P062d Fuel Injector Driver Bank 1
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P062D 00 Fuel injector driver bank 1 (Fuel Injector Driver Circu...

    Other materials:

    Vin Registration
    Description VIN Registration is an operation to registering VIN in ECM. It must be performed each time ECM is replaced.NOTE: Accurate VIN which is registered in ECM may be required for Inspection & Maintenance (I/M). Work Procedure CHECK VIN Check the VIN of the vehicle and note it. Refer ...

    System Description. Component Parts. Electrical Units Location
    Electrical Units Location Component Parts Location No.Component 1. 12V Sub Battery (Lithium Ion Battery) 2. Fusible Link Box (Battery) 3. Battery 4. Relay Box 5. IPDM E/R (Intelligent Power Distribution Module Engine Room) 6. Fusible Link Box (12V Sub B ...

    Fuel Injector Offset Learning
    Description Fuel injector offset learning is an operation to allow ECM to learn fuel injector offset data. This operation must be performed after the following parts are replaced: Each time injector or ECM is replaced. (For details, refer to Work Procedure.) Work Procedure PRECONDITIONI ...