Nissan Rogue (T33) 2021-Present Service Manual: P060a Ecm

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P060a Ecm

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P060A 00

CONTROL MODULE

(Internal control module monitoring processor performance) 		Diagnosis condition Engine running at idle
Signal (terminal) —
Threshold ECM internal monitoring processor is malfunctioning
Diagnosis delay time —

POSSIBLE CAUSE

ECM

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Engine output control

ECM reduces the engine output, according to the rise in engine speed. This reduces the Nissan Ariya vehicle speed to encourage the driver to repair malfunction.

  • Driving at 70 km/h (44 MPH) or more is possible.

NOTE:

This value is a reference value converted from engine power to Nissan Ariya vehicle speed. Actual power limitation value differs due to the malfunctioning part and driving condition.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Electric throttle control cancel mode ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.

or

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Electric throttle control cancel mode ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited. When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

PRECONDITIONING

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition switch ON.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and wait at least 10 seconds.

  2. Turn ignition switch OFF and wait at least 10 seconds.

  3. Repeat step 1 and 2 for 5 times.

  4. Turn ignition switch ON.

  5. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure. Refer to DTC Description.

Is the 1st trip DTC P060A displayed again?

YES>>

Replace ECM. Refer to ECM : Removal & Installation.

NO>>

INSPECTION END

    P0607 Ecm
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0607 00 ECM (Control module performance) Diagnosis condition Ig...
    P060c Ecm
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P060C 00 Control module (Internal Control Module Main Processor ...

    Other materials:

    System Description. Component Parts
    Seat Belt Pre-tensioner with Load Limiter DESCRIPTIONThe seat belt system is equipped with pre-tensioner mechanism, load limiter mechanism, and ELR mechanism.STRUCTURE ELR shaft (torsion bar) Bobbin Lock portion Ring gear Pinion gear Gas generator Sealing element ...

    P051c Crankcase Pressure Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P051C 00 Crankcase Pressure Sensor "A" Circuit Low (Crankcase Pressure Sensor "A" Circuit Low) Diagnosis condition Ignition switch ON Signal (terminal) ...

    P0137 Ho2s2
    DTC Description DTC DETECTION LOGICThe heated oxygen sensor 2 has a much longer switching time between rich and lean than the air fuel ratio (A/F) sensor 1. The oxygen storage capacity of the three way catalyst (manifold) causes the longer switching time. To judge the malfunctions of heated ...