Nissan Rogue (T33) 2021-Present Service Manual: Main Line Between Pwbd and M&a Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Lan System / Can :: Dtc/circuit Diagnosis / Main Line Between Pwbd and M&a Circuit

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side).

    • Harness connector B41

    • Harness connector M69

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the following harness connectors.

    • Automatic back door control unit

    • Harness connectors B41 and M69

  2. Check the continuity between the automatic back door control unit harness connector and the harness connector.

    Automatic back door control unit harness connector Harness connector Continuity
    Connector No. Terminal No. Connector No. Terminal No.
    B55 32 B41 4 Existed
    16 3 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the main line between the automatic back door control unit and the harness connector B41.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of combination meter.

  2. Check the continuity between the harness connector and the combination meter harness connector.

    • With type B meter

      Harness connector Combination meter harness connector Continuity
      Connector No. Terminal No. Connector No. Terminal No.
      M69 4 M76 18 Existed
      3 19 Existed

    • USA production type A meter

      Harness connector Combination meter harness connector Continuity
      Connector No. Terminal No. Connector No. Terminal No.
      M69 4 M73 18 Existed
      3 19 Existed

    • JAPAN production type A meter

      Harness connector Combination meter harness connector Continuity
      Connector No. Terminal No. Connector No. Terminal No.
      M69 4 M77 18 Existed
      3 19 Existed

Is the inspection result normal?

YES (Present error)>>

Check CAN system type decision again.

YES (Past error)>>

Error was detected in the main line between the automatic back door control unit and the combination meter.

NO>>

Repair the main line between the harness connector M69 and the combination meter.

    Main Line Between Anc and Pwbd Circuit
    Diagnosis Procedure CHECK HARNESS CONTINUITY (OPEN CIRCUIT) Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Disconnect the following harne...
    Main Line Between Pwbd and Lib 12v Circuit
    Diagnosis Procedure CHECK HARNESS CONTINUITY (OPEN CIRCUIT) Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Disconnect the following harne...

    Other materials:

    Removal and Installation. Back Door
    Exploded View Roof seal Back door weather-strip Back door hinge LH Back door stay LH* Stud ball Back door bumper rubber upper Back door bumper rubber lower Back door striker TORX bolt Back door panel Back door stay RH* Back door hinge RH ...

    Diagnosis System (tcm)
    Diagnosis Description 1 Trip Detection Diagnosis and 2 Trip Detection Diagnosis NOTE: “Start the engine and turn OFF the ignition switch after warm-up.” This is defined as 1 trip. 1 TRIP DETECTION DIAGNOSISWhen initial malfunction is detected, TCM memorizes DTC. In these diagnoses, some ...

    Air Fuel Ratio Initial Learning
    Description Air fuel ratio initial learning of ECM to learn the air fuel ratio that keeps each engine idle speed within the specific range. It must be performed under any of the following conditions: When ECM is replaced* When engine assembly is replaced* When electric throttle con ...