Nissan Rogue (T33) 2021-Present Service Manual: Magnetic Clutch

Nissan Rogue (T33) 2021-Present Service Manual / Ventilation, Heater & Air Conditioner :: Heater & Air Conditioning Control System / Automatic Air Conditioning :: Dtc/circuit Diagnosis / Magnetic Clutch

Component Function Check

CHECK MAGNETIC CLUTCH OPERATION

CONSULT

  1. Select “HVAC TEST” in “Active test” mode of “HVAC”.

  2. Touch “MODE 1”.

  3. With operating the test item, check magnetic clutch operation by listening and viewing.

Does it operate normally?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK MAGNETIC CLUTCH

CONSULT

  1. Ignition switch ON.

  2. Select “HVAC TEST” in “Active test” mode of “HVAC”.

  3. With operating the test item, check voltage between IPDM E/R harness connector and ground.

    (+) (−) Condition Voltage
    IPDM E/R
    Connector Terminal
    F35 65 Ground Active test: HVAC TEST Off 0 V
    MODE 1 Battery voltage

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace IPDM E/R. Refer to Removal and Installation.

CHECK MAGNETIC CLUTCH POWER SUPPLY CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R connector and A/C compressor connector.

  3. Check continuity between IPDM E/R harness connector and A/C compressor harness connector.

    IPDM E/R A/C compressor Continuity
    Connector Terminal Connector Terminal
    F35 65 F27 1 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair harness or connector.

CHECK MAGNETIC CLUTCH GROUND CIRCUIT FOR OPEN

Check continuity between A/C compressor harness connector and ground.

A/C compressor (—) Continuity
Connector Terminal
F27 2 Ground Yes

Is the inspection result normal?

YES>>

Replace A/C compressor. Refer to Removal and Installation.

NO>>

Repair harness or connector.

    Front Blower Motor
    Diagnosis Procedure CHECK FUSE Ignition switch OFF. Check that the following fusible link are not blown (open). Unit Location Fuse No. Capacity Front blower motor Fuse block (J/...
    Ecv (electrical Control Valve)
    Diagnosis Procedure CHECK FUSE Ignition switch OFF. Check that the following fuse is not blown (open). Unit Location Fuse No. Capacity A/C compressor IPDM E/R 71 10 A Is the fus...

    Other materials:

    C10b4-98 Overheat
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C10B4 98 Overheat (Overheat) Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold System is high temperature status. ...

    Rear Final Drive: R145. Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting
    Noise, Vibration and Harshness (nvh) Troubleshooting NVH Troubleshooting Chart Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts. Possible cause and SUSPECTED PARTS Symptom Reference Noise Vibration Gear tooth rough × – Inspectio ...

    Fonctionnement du système d'intervention de changement de voie intelligent
    Témoin d'activation du système d'intervention de changement de voie intelligent (sur l'écran d'informations du véhicule) Témoin du système d'intervention de changement de voie intelligent (sur l'écran d'informations du véhicule) Écran d'informations du véhicule et commande P ...