Nissan Rogue (T33) 2021-Present Service Manual: Ecv (electrical Control Valve)

Nissan Rogue (T33) 2021-Present Service Manual / Ventilation, Heater & Air Conditioner :: Heater & Air Conditioning Control System / Automatic Air Conditioning :: Dtc/circuit Diagnosis / Ecv (electrical Control Valve)

Diagnosis Procedure

CHECK FUSE

  1. Ignition switch OFF.

  2. Check that the following fuse is not blown (open).

    Unit Location Fuse No. Capacity
    A/C compressor IPDM E/R 71 10 A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK ECV POWER SUPPLY CIRCUIT

  1. Disconnect A/C compressor connector.

  2. Ignition switch ON.

  3. Check voltage between A/C compressor harness connector and ground.

    (+) (−) Voltage
    A/C compressor
    Connector Terminal
    F15 3 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 3.

CHECK ECV POWER SUPPLY CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R connector.

  3. Check continuity between A/C compressor harness connector and IPDM E/R harness connector.

    A/C compressor IPDM E/R Continuity
    Connector Terminal Connector Terminal
    F15 3 F35 71 Yes

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair harness or connector.

CHECK ECV CONTROL SIGNAL CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R connector.

  3. Check continuity between A/C compressor harness connector and IPDM E/R harness connector.

    A/C compressor IPDM E/R Continuity
    Connector Terminal Connector Terminal
    F15 4 F42 98 Yes

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair harness or connector.

CHECK ECV

Check ECV. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Replace A/C compressor. Refer to Removal and Installation.

Component Inspection

CHECK ECV

  1. Ignition switch OFF.

  2. Check continuity between A/C compressor terminals.

Terminal Continuity
3 4 Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace A/C compressor. Refer to Removal and Installation.

    Magnetic Clutch
    Component Function Check CHECK MAGNETIC CLUTCH OPERATION CONSULT Select “HVAC TEST” in “Active test” mode of “HVAC”. Touch “MODE 1”. With operating the test item...
    Ptc Heater
    Component Function Check CHECK PTC HEATER OPERATION Start the engine. Operate front blower motor. Operate temperature control dial to full hot position. Check for warm air at di...

    Other materials:

    Removal and Installation. Driver Knee Air Bag Module
    Exploded View Steering member Driver knee air bag module     : Always replace after every disassembly. : N·m (kg-m, in-lb) Removal and Installation WARNING: Always observe the following items for preventing accidental activation. Before servicing, pla ...

    Removal and Installation. Bcm
    Removal and Installation CAUTION: When replacing the BCM, always replace it with a new one. The functions controlled by the BCM does not operate properly in case of reuse of the BCM from another Nissan Ariya vehicle. Be sure to perform the following items must be performed when replac ...

    Repairing Procedures and Precautions
    Fundamentals of Body Repair Fundamentals of Body Repair There are many kinds of damage caused by collisions.Therefore, the appropriate repair method for the damage should be selected. This section outlines repair methods of major damage and how to use the main tools.BODY REPAIR FLOWCHART ...