Nissan Rogue (T33) 2021-Present Service Manual: C1f80-11 Steering Wheel Touch Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Adas Control Unit :: Dtc/circuit Diagnosis / C1f80-11 Steering Wheel Touch Sensor

Without Propilot Assist 2.1

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1F80 11

Steering wheel touch sensor

(Steering wheel touch sensor) 		Diagnosis condition When engine is running
Signal (terminal) Steering wheel touch sensor status signal (LIN communication signal)
Threshold Receiving voltage error of steering wheel touch sensor
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Steering wheel touch sensor power supply or ground circuit

  • Steering wheel touch sensor

  • ADAS control unit 2

FAIL-SAFE

The following system are cancelled.

  • Vehicle-to-vehicle distance control mode

  • Steering wheel assistance function

  • Conventional (fixed speed) cruise control mode

  • FEB

  • RAB

  • PFCW

  • LDP

  • Blind Spot Intervention

  • TSR

  • DAA

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine, and then wait for 2 seconds or more.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C1F80-11” is detected as the current malfunction in self-diagnosis results of “ICC/ADAS 2”.

Is “C1F80-11” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

With Propilot Assist 2.1

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1F80 11

Steering wheel touch sensor

(Steering wheel touch sensor) 		Diagnosis condition When engine is running
Signal (terminal) Steering wheel touch sensor status signal (LIN communication signal)
Threshold Receiving voltage error of steering wheel touch sensor
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Steering wheel touch sensor power supply or ground circuit

  • Steering wheel touch sensor

  • ADAS control unit 2

FAIL-SAFE

The following system are cancelled.

  • Lane keep function*1

  • Lane keep function*2

  • Lane change support function

  • Overtaking support function

  • Route driving support function

*1: ProPILOT Assist 2.1 display is green

*2: ProPILOT Assist 2.1 display is blue

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine, and then wait for 2 seconds or more.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C1F80-11” is detected as the current malfunction in self-diagnosis results of “ICC/ADAS 2”.

Is “C1F80-11” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

REPLACE STEERING WHEEL

  1. Replace steering wheel. Refer to Removal and Installation.

  2. Perform confirmation procedure again. Refer to DTC Description (Without ProPILOT Assist 2.1) or DTC Description (With ProPILOT Assist 2.1).

Is “C1F80-11” detected as the current malfunction?

YES>>

Replace the ADAS control unit 2. Refer to Removal and Installation.

NO>>

INSPECTION END

    C1f70-87 Ethernet Circuit
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F70 87 Ethernet circuit (Ethernet circuit) Diagnosis co...
    C1f80-88 Steering Wheel Touch Sensor
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1F80 88 Steering wheel touch sensor...

    Other materials:

    Dtc/circuit Diagnosis. B2906-11 Recliner Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detection condition B2906-11 Recliner Sensor Diagnosis condition The Recliner Sensor signal is shorted to ground Signal (terminal) Reclining Motor (terminal #5) Threshold ...

    B2600-42 Configuration Error
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detected condition B2600-42 Configuration error Diagnosis condition After the ignition switch OFF, wait for 1 minutes or more When ignition switch is ON. Signal (terminal) — Threshold ...

    Electric Shift Control Module
    Exploded View Electric shift control module         : N·m (kg-m, in-lb) : Vehicle front Removal and Installation REMOVALDisconnect the negative battery terminal. Refer to Exploded View. Remove instrument side panel LH. Refer to Exploded View. Disconnect the harn ...