Nissan Rogue (T33) 2021-Present Service Manual: Av Branch Line Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Lan System / Can :: Dtc/circuit Diagnosis / Av Branch Line Circuit

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side).

    • AV control unit

    • 8CH CAN gateway

Is the inspection result normal?

YES-1>>

With type B meter: GO TO 2.

YES-2>>

With type A meter: GO TO 3.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of 8CH CAN gateway.

  2. Check the continuity between the 8CH CAN gateway harness connector terminals.

    8CH CAN gateway harness connector Continuity
    Connector No. Terminal No.
    M16 22 19 Existed
    23 20 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check the harness and repair the root cause (IT CAN communication circuit side). Refer to Diagnosis Procedure.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of 8CH CAN gateway.

  2. Check the continuity between the 8CH CAN gateway harness connector terminals.

    8CH CAN gateway harness connector Continuity
    Connector No. Terminal No.
    M45 27 15 Existed
    28 16 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check the harness and repair the root cause (IT CAN communication 2 circuit side). Refer to Diagnosis Procedure.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Connect the connector of 8CH CAN gateway.

  2. Disconnect the connector of AV control unit.

  3. Check the resistance between the AV control unit harness connector terminals.

    • Without BOSE audio system

      AV control unit harness connector Resistance (Ω)
      Connector No. Terminal No.
      M102 21 41 Approx. 54 – 66

    • With BOSE audio system

      AV control unit harness connector Resistance (Ω)
      Connector No. Terminal No.
      M124 21 41 Approx. 54 – 66

Is the measurement value within the specification?

YES>>

GO TO 5.

NO>>

Repair the AV control unit branch line.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the AV control unit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES (Present error)>>

Replace the AV control unit. Refer to Removal and Installation.

YES (Past error)>>

Error was detected in the AV control unit branch line.

NO>>

Repair the power supply and the ground circuit.

    Wl Chg Branch Line Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damag...
    Ivc Branch Line Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damag...

    Other materials:

    Rear Final Drive: R145. Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting
    Noise, Vibration and Harshness (nvh) Troubleshooting NVH Troubleshooting Chart Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts. Possible cause and SUSPECTED PARTS Symptom Reference Noise Vibration Gear tooth rough × – Inspectio ...

    Removal and Installation. Map Lamp
    Exploded View Headlining assembly Map lamp assembly Map lamp housing Bulb Lens Map lamp finisher : Pawl : Metal clip Removal and Installation REMOVALCAUTION: Disconnect the battery negative terminal or remove power circuit fuse when performing t ...

    Accelerator Pedal Position Sensor
    Component Inspection CHECK ACCELERATOR PEDAL POSITION SENSOR Turn ignition switch OFF. Reconnect all harness connectors disconnected. Turn ignition switch ON. Check the voltage between ECM harness connector terminals as per the following condition. ECM Condition Voltage (A ...