Nissan Rogue (T33) 2021-Present Service Manual: Wl Chg Branch Line Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Lan System / Can :: Dtc/circuit Diagnosis / Wl Chg Branch Line Circuit

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side).

    • Wireless charger unit

    • Harness connector M210

    • Harness connector M79

    • 8CH CAN gateway

Is the inspection result normal?

YES-1>>

With type B meter: GO TO 2.

YES-2>>

With type A meter: GO TO 3.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of 8CH CAN gateway.

  2. Check the continuity between the 8CH CAN gateway harness connector terminals.

    8CH CAN gateway harness connector Continuity
    Connector No. Terminal No.
    M16 22 19 Existed
    23 20 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check the harness and repair the root cause (IT CAN communication circuit side). Refer to Diagnosis Procedure.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of 8CH CAN gateway.

  2. Check the continuity between the 8CH CAN gateway harness connector terminals.

    8CH CAN gateway harness connector Continuity
    Connector No. Terminal No. Connector No. Terminal No.
    M45 25 M9 55 Existed
    26 56 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check the harness and repair the root cause (IT CAN communication 1 circuit side). Refer to Diagnosis Procedure.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Connect the connector of 8CH CAN gateway.

  2. Disconnect the connector of wireless charger unit.

  3. Check the resistance between the wireless charger unit harness connector terminals.

    Wireless charger unit harness connector Resistance (Ω)
    Connector No. Terminal No.
    M213 2 6 Approx. 54 – 66

Is the measurement value within the specification?

YES>>

GO TO 5.

NO>>

Repair the wireless charger unit branch line.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the wireless charger unit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES (Present error)>>

Replace the wireless charger unit. Refer to Removal and Installation.

YES (Past error)>>

Error was detected in the wireless charger unit branch line.

NO>>

Repair the power supply and the ground circuit.

    Anc Branch Line Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damag...
    Av Branch Line Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damag...

    Other materials:

    Removal and Installation. Filament
    Inspection and Repair INSPECTIONWhen measuring voltage, wrap tin foil around the top of the negative probe. Then press the foil against the wire with your finger. Attach probe circuit tester (in Volt range) to middle portion of each filament. If a filament is burned out, circuit teste ...

    Vehicle information display warnings and indicators
    Engine start operation indicator This indicator appears when the shift position is set to P (Park). It informs the driver that the engine will start when the ignition switch is pushed while depressing the brake pedal. The Nissan Rogue engine can be started directly in any ignition switch position. ...

    Transfer: Ty92a. Removal and Installation
    Transfer Oil Temperature Sensor Kr15ddt Exploded View Transfer oil temperature sensor Gasket Transfer assembly : N·m (kg-m, ft-lb) : Always replace after every disassembly. Removal and Installation REMOVALRemove engine under cover. Refer to Exploded View. Drain the ...