Nissan Rogue (T33) 2021-Present Service Manual: P1564 Ascd Steering Switch

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P1564 Ascd Steering Switch

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P1564 00

ASCD SW

(ASCD SW) 		Diagnosis condition —
Signal (terminal) ASCD steering switch signal
Threshold ECM detects that input signal from the ASCD steering switch is out of the specified range
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (ASCD steering switch circuit is open or shorted.)

  • ASCD steering switch

  • ECM

FAIL-SAFE

Engine Control System

Not applicable

Stop/Start System

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P1564 is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Ignition switch OFF and wait at least 10 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 10 seconds.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Ignition switch ON.

  2. Wait at least 10 seconds.

  3. Press MAIN switch for at least 10 seconds, then release it and wait at least 10 seconds.

  4. Press CANCEL switch for at least 10 seconds, then release it and wait at least 10 seconds.

  5. Press RES+ switch for at least 10 seconds, then release it and wait at least 10 seconds.

  6. Press SET— switch for at least 10 seconds, then release it and wait at least 10 seconds.

  7. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P1564 is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK ASCD STEERING SWITCH CIRCUIT

With CONSULT

  1. Turn ignition switch ON.

  2. Select “CANCEL SW”, “RES+ SW” and “SET- SW” in “DATA MONITOR” mode of “ENGINE” using CONSULT.

  3. Check each item indication as per the following conditions.

    Monitor item Condition Indication
    MAIN SW MAIN switch Pressed ON
    Released OFF
    CANCEL SW CANCEL switch Pressed ON
    Released OFF
    RESUME/ACC SW RES+ switch Pressed ON
    Released OFF
    SET SW SET- switch Pressed ON
    Released OFF

Without CONSULT

  1. Turn ignition switch ON.

  2. Check the voltage between ECM harness connector terminals.

    ECM Condition

    Voltage

    (Approx.)
    Connector + -
    Terminal
    E21 142 143 MAIN switch: Pressed 0 V
    CANCEL switch: Pressed 1 V
    SET- switch: Pressed 2 V
    RES+ switch: Pressed 3 V
    All ASCD steering switches: Released 4 V

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

GO TO 3.

CHECK ASCD STEERING SWITCH GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Disconnect spiral cable harness connector.

  4. Check the continuity between spiral cable and ECM harness connector.

    + − Continuity
    Spiral cable ECM
    Connector Terminal Connector Terminal
    M30 1 E21 143 Existed

  5. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK ASCD STEERING SWITCH INPUT SIGNAL CIRCUIT

  1. Check the continuity between ECM harness connector and spiral cable.

    + − Continuity
    Spiral cable ECM
    Connector Terminal Connector Terminal
    M30 8 E21 142 Existed

  2. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

CHECK ASCD STEERING SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace ASCD steering switch. Refer to Exploded View.

    P155f Generator Voltage
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P155F 00 GENERATOR VOLTAGE (GENERATOR VOLTAGE) Diagnosis conditi...
    P1564 Propilot Assist Steering Switch
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1564 00 ASCD SW (ProPILOT Assist SW) Diagnosis condition — Si...

    Other materials:

    Av Control Unit
    Nissanconnect with 8" Color Display Reference Value VALUES ON THE DIAGNOSIS TOOLNOTE: The following table includes information (items) inapplicable to this Nissan Ariya vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items. Monitor Item Condition Va ...

    U2118 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U2118 87 CAN comm err (Intelligent Key) [CAN comm err (Intelligent Key)] Diagnosis condition Ignition switch ON Signal (terminal) CAN communication sig ...

    Removal and Installation. Road Wheel Tire Assembly
    Exploded View Tire assembly : N·m (kg-m, ft-lb) Removal & Installation REMOVALRemove wheel nuts. Remove tire assembly.INSTALLATIONNote the following, install in the reverse order of removal. When replacing or rotating wheels, perform following; Perform the ID regist ...