Nissan Rogue (T33) 2021-Present Service Manual: P1564 Propilot Assist Steering Switch

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P1564 Propilot Assist Steering Switch

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P1564 00

ASCD SW

(ProPILOT Assist SW) 		Diagnosis condition —
Signal (terminal) ProPILOT Assist steering switch signal
Threshold ECM detects that input signal from the ProPILOT Assist steering switch is out of the specified range
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (ProPILOT Assist steering switch circuit is open or shorted.)

  • ProPILOT Assist steering switch

  • ECM

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P1564 is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Ignition switch OFF and wait at least 10 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 10 seconds.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Ignition switch ON.

  2. Wait at least 10 seconds.

  3. Press MAIN switch for at least 10 seconds, then release it and wait at least 10 seconds.

  4. Press CANCEL switch for at least 10 seconds, then release it and wait at least 10 seconds.

  5. Press RES+ switch for at least 10 seconds, then release it and wait at least 10 seconds.

  6. Press SET— switch for at least 10 seconds, then release it and wait at least 10 seconds.

  7. Press DISTANCE switch for at least 10 seconds, then release it and wait at least 10 seconds.

  8. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK PROPILOT ASSIST STEERING SWITCH

Check ProPILOT Assist steering switch. Refer to DTC Diagnosis Procedure.

Is the inspection result normal?

YES>>

INSPECTION END.

NO>>

Repair or replace the error-detected parts.

    P1564 Ascd Steering Switch
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1564 00 ASCD SW (ASCD SW) Diagnosis condition — Signal (termi...
    P1568 Icc Command Value
    DTC Description DTC DETECTION LOGICECM detects a difference between signals from ADAS control unit is out of specified range. DTC CONSULT screen terms (Trouble diagnosis content...

    Other materials:

    Dtc/circuit Diagnosis. Memory Indicator
    Component Function Check CHECK FUNCTION Push set switch. Check memory indicator operation. When driver seat position is already retained in memory : Illuminated for 5 seconds When driver seat position is not retained in memory : Illuminated for 0.5 second Is the ins ...

    Timing Chain
    Exploded View 1. Slack guide 2. Timing chain tensioner 3. Oil level gauge guide 4. Oil level gauge 5. Timing chain 6. O-ring 7. O-ring 8. O-ring 9. O-ring 10. Oil filter 11. Valve timing control cover 12. O-ring 13. E ...

    Basic Inspection. Additional Service When Replacing Ecm
    Description Performing the following procedure can automatically activate recommunication of ECM and Intelligent Key unit, but only when the ECM is replaced with a new one*. For details, refer to Work Procedure.*: New one means a virgin ECM that has never been energized on-board.(In this step, ...