Nissan Rogue (T33) 2021-Present Service Manual: Illumination Control Switch Signal Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Information & Multimedia :: Meter, Warning Lamp & Indicator / Type B :: Dtc/circuit Diagnosis / Illumination Control Switch Signal Circuit

Component Function Check

CHECK COMBINATION METER INPUT SIGNAL

  1. Ignition switch ON.

  2. Measure voltage between the following terminals of the combination meter.

    Combination meter Condition

    Voltage

    (Approx.)
    Connector Terminals
    (+) (−)
    M76 25 32 When illumination control switch (+) is pressed 0 V
    Other than the above 5.0 V
    31 When illumination control switch (−) is pressed 0 V
    Other than the above 5.0 V

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK ILLUMINATION CONTROL SWITCH SIGNAL CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect combination meter harness connector and illumination switch harness connector.

  3. Check continuity between combination meter harness connector and illumination control switch harness connector.

    Combination meter Illumination control switch Continuity
    Connector Terminal Connector Terminal
    M76 32 M3 4 Yes
    31 7
    25 6

  4. Check continuity between combination meter harness connector and ground.

    Combination meter — Continuity
    Connector Terminal
    M76 32 Ground No
    31
    25

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair harness or connector.

CHECK ILLUMINATION CONTROL SWITCH

Check illumination control switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Replace illumination control switch. Refer to Removal and Installation.

Component Inspection

CHECK ILLUMINATION CONTROL SWITCH

  1. Ignition switch OFF.

  2. Disconnect illumination control switch connector.

  3. Check continuity between the following terminals of the illumination control switch.

    Terminals Condition Continuity
    Illumination control switch
    6 4 When illumination control switch (+) is pressed Yes
    Other than the above No
    7 When illumination control switch (−) is pressed Yes
    Other than the above No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace illumination control switch. Refer to Removal and Installation.

    Steering Switch Signal B Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL CONSULT Ignition switch ON. Select “Steering switch input” in “Data monitor” mode of “M&A”. Check t...
    Fuel Level Sensor Signal Circuit
    Component Function Check PERFORM COMPONENT FUNCTION CHECK (1) Ignition switch OFF. Disconnect fuel level sensor unit, fuel pump and FPCM (fuel level sensor) (main) harness conne...

    Other materials:

    Cockpit
    Steering Assist switch* (models with ProPILOT Assist) — activates steering support features available on the Nissan Rogue.* Head Up Display (HUD) switch* — controls the HUD system that projects key driving information onto the windshield.* Headlight and turn signal switch — operates ...

    Fonctionnement du système de freinage d'urgence automatique avec détection des piétons
    Témoin d'avertissement du système de freinage d'urgence automatique Témoin de détection du véhicule à l'avant (affiché sur l'écran d'informations du véhicule) Témoin d'avertissement de désactivation du système de freinage d'urgence automatique (tableau de bord) Commandes a ...

    Ambient Sensor Signal Circuit
    Diagnosis Procedure CHECK AMBIENT SENSOR POWER SUPPLY Ignition switch OFF. Disconnect ambient sensor harness connector. Ignition switch ON. Check voltage between ambient sensor harness connector and ground. (+) (–) Voltage (Approx.) Ambient sensor Connector Termin ...