Nissan Rogue (T33) 2021-Present Service Manual: Ignition Relay-2

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Power Control System / Power Distribution System :: Dtc/circuit Diagnosis / Ignition Relay-2

Diagnosis Procedure

CHECK IGNITION RELAY-2 POWER SUPPLY

  1. Disconnect ignition relay-2 connector.

  2. Check voltage between ignition relay-2 harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    Ignition relay-2
    Connector Terminal
    J-1 2 Ground Battery voltage
    3

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace harness or connectors.

CHECK IGNITION RELAY-2

Check ignition relay-2. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace ignition relay-2.

CHECK IGNITION RELAY-2 CONTROL SIGNAL CIRCUIT

  1. Disconnect BCM connector.

  2. Check continuity between BCM harness connector and ignition relay-2 harness connector.

    With type A meter
    BCM Ignition relay-2 Continuity
    Connector Terminal Connector Terminal
    M51 31 J-1 1 Yes
    With type B meter
    BCM Ignition relay-2 Continuity
    Connector Terminal Connector Terminal
    M18 33 J-1 1 Yes

  3. Check continuity between BCM harness connector and ground.

    With type A meter
    BCM — Continuity
    Connector Terminal
    M51 31 Ground No
    With type B meter
    BCM — Continuity
    Connector Terminal
    M18 33 Ground No

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness or connectors.

Component Inspection

CHECK IGNITION RELAY-2

  1. Ignition switch OFF.

  2. Disconnect ignition relay-2 connector.

  3. Check continuity between ignition relay-2 terminals.

Ignition relay-2 Condition Continuity
Terminals
12 V direct current supply between terminals and . Yes
No current supply No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace ignition relay-2.

    Ignition Relay-1
    Diagnosis Procedure CHECK IGNITION RELAY-1 POWER SUPPLY Disconnect ignition relay-1 connector. Check voltage between ignition relay-1 harness connector and ground. (+) (–) Vol...
    Ignition Relay-3
    Diagnosis Procedure CHECK IGNITION RELAY-3 POWER SUPPLY Disconnect ignition relay-3 connector. Check voltage between ignition relay-3 harness connector and ground. (+) (–) Vol...

    Other materials:

    2wd. Preparation. Preparation
    Preparation Special Service Tool Tool number (TechMate No.) Tool name Description KV40104000 ( – ) Hub lock nut wrench a: 85 mm (3.35 in) b: 65 mm (2.56 in) Removing and Installing wheel hub lock nut. KV40107300 ( – ) Boot band crimping tool Installing bo ...

    Dtc/circuit Diagnosis. B1002-13 Lap Pre-Tensioner Rh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B1002-13 Lap pre-tensioner RH (Lap pre-tensioner right hand) Diagnosis condition When ignition switch is ON. Signal (terminal) Lap pre-tensioner RH signal ...

    P02ee Fuel Injector
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P02EE 00 Cylinder 1 injector (Cylinder 1 Injector Circuit Range/Performance) Diagnosis condition Injector compensation control is operating Signal — ...