Nissan Rogue (T33) 2021-Present Service Manual: P02ee Fuel Injector

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P02ee Fuel Injector

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P02EE 00

Cylinder 1 injector

(Cylinder 1 Injector Circuit Range/Performance) 		Diagnosis condition Injector compensation control is operating
Signal —
Threshold When the injector compensation value is above or below the threshold value.
Diagnosis delay time —

POSSIBLE CAUSE

  • ECM

  • Fuel injector

  • Harness or connectors (Fuel injector circuit is open or shorted.)

FAIL-SAFE

Engine Control System

Not applicable

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited. When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE-1

  1. Start the engine.

  2. Let engine idle for 20 seconds.

  3. Check the DTC.

Is the DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK FUEL INJECTOR

Check fuel injector. Refer to Component Function Check.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

REPLACE ECM

  1. Replace ECM. Refer to ECM : Removal & Installation.

  2. Perform DTC confirmation procedure again. Refer to DTC Description.

  3. Check the DTC.

Is the DTC P02EE displayed again?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

INSPECTION END

    P02cc Fuel Injector
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P02CC 00 CYL1 INJECTOR OFFSET LEARNING (Cylinder 1 Fuel Injector...
    P0300 Misfire
    DTC Description DTC DETECTION LOGICWhen a misfire occurs, engine speed will fluctuate. If the engine speed fluctuates enough to cause the crankshaft position (CKP) sensor signal...

    Other materials:

    Symptom Diagnosis. Ign Off Interlock Door Unlock Function Does Not Operate
    Diagnosis Procedure CHECK “AUTO DOOR UNLOCK” SETTING IN COMBINATION METER Check “Auto Door Unlock” setting is “IGN OFF”. Is the inspection result normal? YES>> GO TO 2. NO>> Set “IGN OFF” in combination meter. REPLACE BCM Replace BCM. Refer to Removal and I ...

    Dtc/circuit Diagnosis. Combination Switch Output Circuit
    Diagnosis Procedure CHECK OUTPUT CIRCUIT Ignition switch ON. Turn ON any switch in the system that is malfunctioning. Check duty ratios between BCM harness connector and ground by using an oscilloscope. With type A meter System + − Voltage (Approx.) BCM Connector Termi ...

    Dtc/circuit Diagnosis. B2c41-04 Power Window Motor Fl
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2C41-04 Power window motor FL [Front power window motor (driver side)] Diagnosis condition When ignition switch ON or power window timer operates. Signal (ter ...