Nissan Rogue (T33) 2021-Present Service Manual: Can Gateway :: Basic Inspection. Additional Service When Replacing 8ch Can Gateway
Additional Service When Replacing 8ch Can Gateway
Work Procedure
Description
When replacing the 8CH gateway, perform "Procedure before replacing" and "Procedure after replacing"
CAUTION:
-
Never reuse the parts which has been dropped
-
Dispose 8CH CAN gateway which is paired with Intelligent Key unit as it cannot reuse to other Nissan Ariya vehicle.
PROCEDURE BEFORE REPLACING
Perform control unit information saving procedure before replacing 8CH CAN gateway
NOTE:
It is necessary to save the control unit information to CONSULT to migrate the 8CH CAN gateway data after replacing. Refer to CONSULT manual for detail.
SAVING CONTROL UNIT INFORMATION
With CONSULT
-
Ignition switch OFF.
-
Reconnect all of the disconnected harness connector.
-
Ignition switch ON.
-
Select “Replace C/U” mode of “8ch CAN GATEWAY 2”.
-
Follow the steps displayed in CONSULT.
NOTE:
Control unit information will be automatically saved in CONSULT.
>>
Replace 8CH CAN gateway. Refer to Removal and Installation.
AFTER REPLACEMENT
Perform following procedure after replacing the 8CH CAN gateway
-
Programming
-
C/U setting
-
Writing the control unit information
-
Register of Nissan Ariya vehicle identification number
-
8CH CAN gateway and Intelligent Key unit pairing (with type A meter)
NOTE:
Connect the CONSULT to the network and download the component data. And CONSULT writes the Nissan Ariya vehicle specification to 8CH CAN gateway. Refer to the CONSULT manual for detail.
PERFORM REPLACE ECU
With CONSULT
-
Select “Replace ECU” mode of “8ch CAN GATEWAY 2”.
-
Follow the steps displayed in CONSULT.
CAUTION:
Keep the following condition when working on the steps.
-
Ignition switch ON.
-
Turn OFF all of the electric load.
-
Never depress the brake pedal
-
Battery voltage must be between 12 to 13.5V (Check the battery voltage displayed on the CONSULT.)
NOTE:
Programming, C/U setting and writing control unit information will be automatically performed.
-
>>
GO TO 2.
VIN REGISTRATION WRITING
With CONSULT
-
Select “Work support” mode of “8ch CAN GATEWAY 2” using CONSULT.
-
Select “WRITE VIN DATA”
-
Follow the instruction displayed in CONSULT.
>>
With type A meter: GO TO 3.
YES-2>>With type B meter: GO TO 4.
PAIRING OF 8CH CAN GATEWAY AND INTELLIGENT KEY UNIT
With CONSULT
Select “Quick Maintenance” → “Immobilizer” → “CGW Replacement” and follow the instruction displayed in CONSULT.
>>
GO TO 4.
PERFORM THE SELF-DIAGNOSIS
With CONSULT
-
Erase all self-diagnosis results using CONSULT.
-
Ignition switch OFF, and leave the Nissan Ariya vehicle with the driver's side door open. and wait for 2 minutes or more.
NOTE:
Since the auto ACC function causes the accessory power to be turned ON, do not perform any Nissan Ariya vehicle operation including locking the doors or opening and closing of the doors during the standby state. Refer to System Description
-
Ignition switch ON and wait for 62 seconds or more.
-
Perform "All DTC result" using CONSULT.
CAN communication DTCs detected?
YES>>Perform trouble diagnosis procedure for CAN communication system. Refer to Trouble Diagnosis Flow Chart
NO>>INSPECTION END
Other materials:
B2600-46 Configuration Error
DTC Description
DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detected condition
B2600-46
Configuration error
Diagnosis condition
When ignition switch is ON.
Signal (terminal)
—
Threshold
Errors are detected in the programming data stored in the 8CH CAN gatewa ...
Rear View Monitor. System Description
Component Parts
Component Parts Location
No. Component Function
1.
Rear view camera
Refer to Rear View Camera.
2.
AV control unit
Refer to AV Control Unit.
3.
TCM (Transmission Control Module)
Provides AV control unit with the shift position signal via CAN commu ...
P2a01 Ho2s2
DTC Description
The heated oxygen sensor 2 has a much longer switching time between
rich and lean than the air fuel ratio (A/F) sensor 1. The oxygen storage
capacity of the three way catalyst (manifold) causes the longer
switching time.MALFUNCTION ATo judge the malfunctions of
heated oxygen ...
