Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B1002-13 Lap Pre-Tensioner Rh

Nissan Rogue (T33) 2021-Present Service Manual / Restraints :: Srs Air Bag Control System / Dtc/circuit Diagnosis :: B1002-13 Lap Pre-Tensioner Rh

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B1002-13

Lap pre-tensioner RH

(Lap pre-tensioner right hand) 		Diagnosis condition When ignition switch is ON.
Signal (terminal) Lap pre-tensioner RH signal
Threshold Lap pre-tensioner RH circuit is open
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

  • Connection malfunction or open circuit of harness and connector

  • Internal malfunction of lap pre-tensioner RH

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF DIAGNOSIS RESULT

CONSULT

  1. Ignition switch ON.

  2. Perform “Self diagnosis result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End

Diagnosis Procedure

WARNING:

  • Before servicing, ignition switch OFF, disconnect battery negative terminal and wait at least 3 minutes. (To discharge backup capacitor.)

  • Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace wiring harness.

REPLACE LAP PRE-TENSIONER RH

  1. Replace lap pre-tensioner RH. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 4.

NO>>

Inspection End

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

  1. Replace air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 1.

NO>>

Inspection End

    Dtc/circuit Diagnosis. B1002-12 Lap Pre-Tensioner Rh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B1002-12 Lap pre-tensioner RH (Lap pre-tensioner right hand)...
    Dtc/circuit Diagnosis. B1002-1a Lap Pre-Tensioner Rh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B1002-1A Lap pre-tensioner RH (Lap pre-tensioner right hand)...

    Other materials:

    U224a-87 Can Comm Err (awd/4wd)
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U224A 87 CAN comm err (AWD/4WD) [Controller area network communication error (AWD/4WD control unit)] 1 Diagnosis condition When ignition switch is ON. ...

    C1203-86 Abs Signal
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition C1203-86 ABS SYSTEM (Antilock brake system) Diagnosis condition Ignition switch: ON Nissan Ariya Vehicle running Signal Wheel speed signals ...

    Steering Switch Signal B Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL CONSULT Ignition switch ON. Select “Steering switch input” in “Data monitor” mode of “M&A”. Check that the function operates normally according to the following conditions: Condition Value CONTRO ...