Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Thigh Support Switch

Component Function Check

CHECK FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “Thigh support switch (Up)” and “Thigh support switch (Down)” in “Data monitor” mode of “DRIVER SEAT”.

  3. Check thigh support switch signal under the following conditions.

Monitor item Condition Status
Thigh support switch (Up) Thigh support switch Operate (upward) On
Release Off
Thigh support switch (Down) Thigh support switch Operate (downward) On
Release Off

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK THIGH SUPPORT SWITCH POWER SUPPLY VOLTAGE

  1. Ignition switch OFF.

  2. Disconnect power seat switch LH connector.

  3. Ignition switch ON.

  4. Check voltage between power seat switch LH harness connector and ground.

    (+) (-)

    Voltage

    (Approx.)
    Power seat switch LH
    Connector Terminal
    B215 2 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 2.

CHECK THIGH SUPPORT SWITCH SIGNAL CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect driver seat control unit connector.

  3. Check continuity between power seat switch LH harness connector and driver seat control unit harness connector.

    Power seat switch LH Driver seat control unit Continuity
    Connector Terminal Connector Terminal
    B215 2 B213 7 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

CHECK THIGH SUPPORT SWITCH SIGNAL CIRCUIT (SHORT TO GROUND)

Check continuity between power seat switch LH harness connector and ground.

Power seat switch LH (—) Continuity
Connector Terminal
B215 2 Ground No

Is the inspection result normal?

YES>>

Replace driver seat control unit. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

CHECK THIGH SUPPORT SWITCH

Check thigh support switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace power seat switch LH. Refer to Removal and Installation.

Component Inspection

CHECK THIGH SUPPORT SWITCH

  1. Ignition switch OFF.

  2. Disconnect power seat switch LH connector.

  3. Check resistance between power seat switch LH terminals.

    Power seat switch LH Condition Resistance: kΩ
    Terminal
    2 4 Thigh support switch Operate (upward) 0.399 – 0.455
    Operate (downward) 0.241 – 0.287
    Release 7.276 – 8.235

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace power seat switch LH. Refer to Removal and Installation.

    Dtc/circuit Diagnosis. Reclining Switch
    Component Function Check CHECK FUNCTION CONSULT Ignition switch ON. Select “Reclining switch (Forward)” and “Reclining switch (Backward)” in “Data monitor” mode of ...
    Symptom Diagnosis. Manual Function Does Not Operate
    All Component Diagnosis Procedure CHECK DRIVER SEAT CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT Check driver seat control unit power supply and ground circuit. Refer to Diagnos...

    Other materials:

    P02cd Fuel Injector
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P02CD 00 CYL1 INJECTOR OFFSET LEARNING (Cylinder 1 Fuel Injector "A" Offset Learning At Max Limit) Diagnosis condition Engine running During injector ...

    C106f-54 Steering Angle Sensor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C106F 54 Steering angle sensor (Steering angle sensor) Diagnosis condition When ignition switch is ON. When the power supply voltage is normal. ...

    Automatic air conditioner (models without rear control)
    Models with heated steering wheel Models without heated steering wheel Basic information Temperature control dial (driver's side) AUTO button Display screen SYNC button Temperature control dial (passenger's side) ON·OFF button Air recirculation button Fan speed buttons Air flow ...