Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Reclining Switch

Component Function Check

CHECK FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “Reclining switch (Forward)” and “Reclining switch (Backward)” in “Data monitor” mode of “DRIVER SEAT”.

  3. Check reclining switch signal under the following conditions.

Monitor item Condition Status
Reclining switch (Forward) Reclining switch Operate (forward) On
Release Off
Reclining switch (Backward) Reclining switch Operate (backward) On
Release Off

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK RECLINING SWITCH POWER SUPPLY VOLTAGE

  1. Ignition switch OFF.

  2. Disconnect power seat switch LH connector.

  3. Ignition switch ON.

  4. Check voltage between power seat switch LH harness connector and ground.

    (+) (-)

    Voltage

    (Approx.)
    Power seat switch LH
    Connector Terminal
    B215 3 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 2.

CHECK RECLINING SWITCH SIGNAL CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect driver seat control unit connector.

  3. Check continuity between power seat switch LH harness connector and driver seat control unit harness connector.

    Power seat switch LH Driver seat control unit Continuity
    Connector Terminal Connector Terminal
    B215 3 B213 11 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

CHECK RECLINING SWITCH SIGNAL CIRCUIT (SHORT TO GROUND)

Check continuity between power seat switch LH harness connector and ground.

Power seat switch LH (—) Continuity
Connector Terminal
B215 3 Ground No

Is the inspection result normal?

YES>>

Replace driver seat control unit. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

CHECK RECLINING SWITCH

Check reclining switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace power seat switch LH. Refer to Removal and Installation.

Component Inspection

CHECK RECLINING SWITCH

  1. Ignition switch OFF.

  2. Disconnect power seat switch LH connector.

  3. Check resistance between power seat switch LH terminals.

    Power seat switch LH Condition Resistance: kΩ
    Terminals
    3 4 Reclining switch Operate (forward) 0.399 – 0.455
    Operate (backward) 0.241 – 0.287
    Release 7.276 – 8.235

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace power seat switch LH. Refer to Removal and Installation.

    Dtc/circuit Diagnosis. Sliding Switch
    Component Function Check CHECK FUNCTION CONSULT Ignition switch ON. Select “Sliding switch (Forward)” and “Sliding switch (Backward)” in “Data monitor” mode of “DR...
    Dtc/circuit Diagnosis. Thigh Support Switch
    Component Function Check CHECK FUNCTION CONSULT Ignition switch ON. Select “Thigh support switch (Up)” and “Thigh support switch (Down)” in “Data monitor” mode of ...

    Other materials:

    B2730-13 Side Sensor [rl]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2730-13 SIDE SENSOR [RL] (Side sensor [RL]) Diagnosis condition When ignition switch is ON Signal (terminal) Rear sonar sensor signal LH side Threshold H ...

    P2135 Tp Sensor
    DTC Description DTC DETECTION LOGICNOTE: If DTC P2135 is displayed with DTC P06B0, first perform the trouble diagnosis for DTC P06B0. Refer to DTC Description. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2135 00 TP SENSOR-B1 (Throttle/Pedal ...

    System maintenance
    To ensure proper operation of the driver monitoring system on the Nissan Rogue, keep the camera and surrounding area clean. Use a soft, damp cloth—such as one designed for lens cleaning—wrung out thoroughly, and gently wipe the surface to remove dust or dirt. License information (ProPILOT Ass ...